plastic bonsai pot mold , steel moulds for aluminum pots plastic bonsai pot mould seller

Super Quality high precision Plastic Injection Moulding parts,OEM/ODM Custom injection plastic moulding product for gasmeter

shaping mold : plastic injection mould

Material As  you request, can be PE / PVC / PP / PS / ABS / PC / POM / Nylon / PET / PPO / PU / EP / UP / Acrylic

Surface treatment: polish Deburring,etc,as you request

injection mould life:45#:50000-100000shots

                                  P20:200000-300000shots

                                  718:300000-400000shots

                                  H13:500000shots

corrugated box for plastic injection parts, wooden case for injection mold

Gate type:Cold runner or hot runner

platic injection mold workshop show:

Plastic prodcust show:

Features

1,plastic pre-treatment for abs injection molding 

ABS water absorption ratio is about 0.2% -0.8%. for the normal ABS before molding ,itsdrying time in oven is for 2-4 hours at 80-85 ℃ ,or in hopper 80 ℃ at 1-2 hours. if PC material mixed with heat-resistant grade ABS, its drying temperature should be increased to 100 ℃. The proportion of the recycled ABS materials can not exceed 30%, electroplating grade ABS can not be used again at plastic injection moulding manufacturer facilities.

2, mold and gate design

The mold for abs injection temperature can be set to 60-65 ℃. Runner diameter is 6-8mm. Gate width is

3mm, if the thickness of the article should be same as gate, the gate length is less than 1mm. Vent width 4-6mm, and its thickness 0.025-0.05mm.

3.Melt temperature

Melt temperature could be decided by Air injection . Different grades of ABS means that their melt

temperatures are also different, we recommend the following settings for plastic injection moulding manufacturer:

Impact resistance grade: 220 ℃ -260 ℃, 250 ℃ better

Plating grade: 250 ℃ -275 ℃, 270 ℃ better

Heat-resistance grade: 240 ℃ -280 ℃, 265 ℃ -270 ℃ better

Flame Retardant grade: 200 ℃ -240 ℃, 220 ℃ -230 ℃ better

Transparent grade: 230 ℃ -260 ℃, 245 ℃ better

Glass fiber reinforced grade: 230 ℃ -270 ℃

High requirements for products surface is, the higher melt temperature and mold temperature should be.

4, the injection speed

Flame Retardant grade with slow speed, Heat-resistance grade with quick speed. abs injection molding products with high surface requirements should take use of high-speed and multi-stage injection rate .

5, back pressure

Back pressure should be as low as possible under normal circumstances, the normal back pressure is 5 bar.

6, residence time in barrel

At a temperature of 265 ℃, maximum of 5-6 minutes residence time in the barrel . Flame Retardant grade

ABS is even shorter.For the downtime, it should set the temperature as low as 100 ℃, and then clean up

barrel with the melting common grade ABS . after cleaning up,the mixture should be put into cold water to prevent further decomposition. if ABS need to replace the other material used, it firstly need clean up barrel with PS, PMMA or PE. Some ABS products is without any problems after releasing from the mold , but over a period of time, they could be discolored,for it may be overheating or melting plastic staying too long in barrel.

8, the products after-treatment,

ABS injection moulding products generally do not need the further treatment, only plating grade products should be subject to heat (70-80 ℃ ,2-4 hours) to remove the surface traces.Electroplated products could

not use release agents, and products should be packaged immediately after removing from the mold .

9, other issues

There are several grades of ABS (especially flame retardant grade), after the plasticizing , its adhesion

force is large on the screw, after long time it will decompose. When that happens, we need to pull, wipe and clean up the screw regularly with PS and other plastic material.

Plastic injection mold show: