Fiber optic christmas tree light power supply adapter 12v dc 72w
Label |
1. Specification
model | output voltage | Current | power | Tol. | R&N | Effi. |
SMT-012-072VP | 12V | 6.0A | 72W | ±3% | 80mV | >82% |
SMT-024-072VP | 24V | 3.0A | 72W | ±2% | 180mV | >82% |
2. INPUT REQUIREMENTS
2.1 Operating range: 90-264VAC
2.2 Rated Input Voltage :100-240VAC
2.3 Input Frequency Range: 50/60Hz +/-3Hz
2.4 Input In-rush Current: 100A max
2.5 Input Current:1.5A max
3.OUTPUT REQUIREMENTS
3.1 Output Voltage and Current
Output | Output Regulation(V) | No Load | Rating Load (A) | |
Voltage(V) | Minimum | Maximum | Current(A) | Continuous Current(A) |
12V | 11.4V | 12.6V | 0A | 6.0A |
3.2 Output Voltage Regulation
The total output voltage regulation shall be +/-5%,including the effects of line voltage variations,load current,ripple and noise,and the AC component of the load current.
3.3 Output Voltage Ripple
The switching power supply shall not exceed the following limits in the indicated voltage for 60Hz or 50Hz ripple,switching frequency ripple and noise measured with 20MHz width.
Ripple and Noise:50/60Hz Ripple + Switching Ripple and Noise
Output | Ripple |
0-6.0A | 200mV |
Ripple and Noise are measured at the end of output cables which are added a
0.1uF(104) Ceramic capacitor and a 22uF Electrolytic capacitor.
4. EFFICIENCY
When 220VAC line input voltage (100-240 VAC),the efficiency shall be >82% at rating load.
5. DIELECTRIC STRENGTH (Hi-Pot) TEST
Finished product withstands with AC3000Vrms/50Hz,5mA max,
primary to secondary, 1 minute for type test,1 second for production test.
6. INSULATION RESISTANCE
Primary to secondary: 10MΩ min at 500VDC.
7. PROTECTION
7.1 Short Circuit Protection
If short circuit occurs,all the output should be protected. After the fault, the adapter automatically recovers.
7.2 Over Shoot
The Output over shoot at turn-on shall not exceed 10% of normal voltage value with or without the load connected.
7.3 Start-up time
The start-up time is less than 2 second.
8.ENVIRONMENTAL CONDITIONS
8.1 Temperature
Operating temperature: 0℃ to +40℃
Storage temperature : -20℃ to +60℃
8.2 Humidity
Relative humidity:≤95%
8.3 Operating Ambient Altitude
Altitude:0-3000m
8.4 Operating at the lower temperature
At -0℃,with the rated voltage 100-240Vac charged to the primary and unloaded and full load on the secondary 8 hours, no abnormality in electric and mechanical characteristic, after 2 hours recovery at the room temperature.
8.5 Operating at the high temperature
At +40℃,with the rated voltage 100-240Vac charged to the primary and unloaded and full Load on the secondary 8 hours, no abnormality in electric and mechanical characteristic, after 2 hours recovery at the room temperature.
9. COOLING
Cooling shall be with natural convection cooling.
10.Burn-in
The burn-in test will be performed at least 4 hours at centigrade
degrees under full load Condition.
11.Referenced standard
11.1 EMI Standards
Reference EN50082-1,EN55022-B,GB-17625.1-2003, GB-9254-1998
EN55013 EN55020
11.2 Safety Standards
The adapter shall be meet certified with the following safety standards.
EN61347,GB4943-2001, J55013,J55020,J60065
12. MOUNTING CONNECTORS
12.1 AC Input Connector
Spec :2Pin
12.2 DC Output Cable
Wire : (Optional) SPT-1 18AWG*2C L=1200mm Color: Black
Plug : (Optional) 5.5 x 2.1x 10mm
13. MECHANICAL FEATURES
13.1 Dimension(Size)
Length: 119.5mm
Width: 62.5mm
Height: 33.5mm
13.2 Vibration and shock
No Evidence of any mechanical or functional damage after the vibration and shock testing.
Test conditions | Acceptance Criteria | |
Frequency | 10-55Hz | Nominal functional test should be satisfied after the test |
Sweep | For each axis(X,Y,Z) | |
Displacement | 0.15mm | |
Periodicity | 10 |
14 . DIAGRAM DATA
14.1. APPEARANCE DRAWING:(Unit:mm)
14.2. NAME PLATE: (Unit:mm)
NOTE: MATERIAL:POLYESTER COATIONG:0.10+/-0.03mm
14.3. DIMENSION OF OUTPUT PLUG & DC CORD:(Unit:mm)
What kind of LED Driver/Power Supply Smarts Electronics do?
We specialized in constant voltage & current LED drivers, 010v/triac/DALI dimmable led drivers, enclosure power suppliers, power adapters.
Our Market
Our major markets are in EU & North America,it takes about 85% markets share. view transaction history
Certifications
Our Services
What Service we can supply??
FAQ
Q1. What's the trade terms you can do??
A1: We accept EXW,FOB..(Optional)
Q2. What's shipping mode can we choose?
A2: Express, Ocean and air transportation (optional).
Q3. What's the MOQ?
A3: Our MOQ is 1pcs. better price for large quantity;
Q4. What can you do if the product is broken?
A4: We promise to replace new ones to you if there is any defective happen during the warranty period.
Q5. Can i get products with my own logo??
A5: Sure, you can, MOQ is 500pcs.
Q6. Can i get a sample for testing??
A6: Sure, but sample fees should be charged on your account.
Q7. What's the mormal lead time??
A7: 7 working days for samples, 15 working days for mass production.
Q8. What's the payment conditon?
A8: T/T in advance or 30% deposit and 70% before delivery (optional)
Q9. What's the Payment do you have?
A9: We accept payment be sent via T/T, L/C, Trade Assurance, WESTERN UNION, PAYPAL.
Q10.How to contact with me??
A9: Skype: steven821228
Send your inquiry details in the below for professional reply,
click " send " now !