Wire Flame Spray Gun 14M

The 14M Flame Spray Gun is a lightweight wire spray gun that uses an air turbine to draw wire in, melt it with fuel gas and blast the molten particles on to the substrate. This gun is suitable for coating both high & low melting wires such as Aluminium, Babbitt, Molybdenum, Copper, Brass etc. Wires of sizes such as 1/8", 5/32" & 3/16" (3.17, 3.96, 4.76mm) can be sprayed easily. This versatile gun has a convenient wire feed thumb trigger making it an excellent choice for hand-held use. The Metal Coat Flame Spray Gun 14M has a universal gas head, which can be adapted to use Oxy/Acetylene or Oxy/Propane fuel gas. The standard gun is set up to spray 1/8" wire using acetylene as the fuel gas. Suitable hardware is available for handling all standard wire sizes ranging from 3/16" down to 1/16". Although the 14M Flame Spray Gun has been designed primarily for hand-held operation, a simple, rugged tool post fixture is supplied with each unit to permit mounting on a machine tool such as a lathe. Powered by compressed air and Oxy/Acetylene or Oxy/Propane, the entire system (except the compressor), can be mounted on a cart for mobile applications and field repair work.

Uses
Flame sprayed coatings with hard & soft wires

Advantages
Wire feed can be controlled very easily with a thumb trigger.
Light Weight
Easy to operate

OPTIONAL ACCESSORIES
Extension Nozzles: Where deep bores or recesses are to be sprayed, a range of extension nozzles are available These allow access of the spray at depths up to 1.1 Mtr., whilst straight or deflector air caps can be selected to direct the spray stream to the area required. Typical use include spraying in internal diameter or hard to reach coating surfaces.

Air Control Unit: Consists of air filter cum regulator for secondary filtration and regulating air flow to wire flame spray gun. An additional outlet provides connections for operator's helmet. Pressure Rating: 10 Bar

Hose Kit: Consist of Hose to connect oxygen cylinder & fuel gas cylinder with gas flow meter to spray gun.

Gas Flow Meter: These precision wall mounting Flowmeters are recommended to use with Flame Spray Equipment. Ease of reading enables economic operation and rapid fault diagnosis. The unit incorporates separate flowmeter for both Oxygen and Fuel Gas supplies.

Air Flow Meter with Hose: The 3AFM Air Flow Meter is a highly accurate rugged and reliable instrument for regulating and measuring the flow of compressed air in a manual powder or wire combustion spray system.

Model: 3AFM (Air Flow Meter) Flow Unit in both NLPM & SCFM

Wire Control Unit: The Wire Reel Stand with Straightener is specifically designed to dispense wires for flame spraying. A wire straightener is included and the unit is capable of handling either reeled or loose coiled wire or spool.

Spray Booth: It is used for controlling sprayed dust and fumes when metallizing operation takes place. It carries away metal dust particles as well as heat. Duct work has adjustable pipe length as well as ball joint to fit individual requirement.

Metal Spray Wire: Standard materials wires such as Aluminium, Aluminium Alloy, Tin, Tin Alloy,Nickel, Nickel Alloy, Zinc, Stainless Steel, Brass, Molybdenum, Monel, Copper & many more are available.

SAFETY WEARS
Metallizing Helmet
Air Breather
Helmet Air Conditioner
Ear Muff
Protective Glass
Safety Mask
Hand Gloves

The supplied system is subjected to warranty against manufacturing defects, faulty material and poor workmanship and which have been reported to METAL COAT, in writing of such defect. The warranty period is 12 months from the date of commissioning or 15 months from the date of supply whichever is earlier. The warranty does not include damages caused due to mishandling or improper/incomplete compliance of operating instructions recommended by us. Warranty is applicable to the extent of free of cost repair/replacement as deemed fit by us.