Wholesale Thermal Adhesives Lc1001 Thermally Conductive Silicone Glue Silicone Gel Adhesive Sealant Rtv Grey
Wholesale Thermal Adhesives Lc1001 Thermally Conductive Silicone Glue Silicone Gel Adhesive Sealant Rtv Grey
| Performance Evaluation | LC1001 | |
| Uncured | Appearance | White, Semiliquid |
| Relative Density (g/cm3) | 1.6~1.65 | |
| Adhesion (cps) | 80000~90000 | |
| TFT min (min℃) | ≤10 | |
| Curing Time(d) | 3~7 | |
| Curing Type | One component deethanol type | |
| Cured | Tensile Strength(MPa) | ≥1.5 |
| Elongation at Break (%) | 200~400 | |
| Hardness(Shore A) | 35~45 | |
| Shear Strength(MPa | ≥1.0 | |
| Peel Strength(N/mm | ≥5 | |
| Linear Shrinkage(%) | ≤0.5 | |
| Conductivity (W/m·k) | ≥1.2 | |
| Voltage Resistivity (Ω·cm) | 3×1015 | |
| Dielectric strength (kV/m· m) | 20 | |
| Permittivity (1.2MHz) | 2.8 | |
Packing Specification: 100ML/ 100PCS/Carton,300ML/25PCS/Carton,2.6L/4PCS/Carton
LC1001 Thermal Conductive Silicone Glue
LC1001 is the semi-flowing heat-resistant silicone adhesive sealant which is made of special silicone rubber material the addition of thermal powders. With excellent conductivity,V0 flame retardant grade, excellent temperature resistance, can be in the range of 60 ~ 280 ℃ Long-term use. As well as good adhesion, long term use will not fall off, will not produce Contact gap to reduce thermal conductivity, moisture-proof, anti-seismic, anti-leakage and aging .The properties are widely used for the adhesion and sealing of the electronic components with high thermal conductivity, which is a single part of the acetone oxime type, It can be cured silicone rubber and conforms to the requirements of ROHS REACH.
Typical Applications
High power LED lamps and lanterns, electrical power, microwave oven, electronic components and other industrial products of thermal conductive adhesive sealing, alternative thermal conductive silicone used in high-power electric module and radiator thermal conductivity between fixed filling adhesive, no card buckle screw, more reliable filling heat, simple process and lower cost.
Applying Process
1. Surface clean : Clean the surface of the adhesive object and remove the rust, dust and oil.
2. Sizing: Twist the cap of the hose, squeeze the gel into the clean surface, and make it natural.
3. Curing: Place the bonded or sealed parts in the air while them to solidify naturally. Curing is a process from surface to the internal, within 24 hours (at room temperature and 55% relative humidity) will cure the depth of the 2 ~ 4 mm, if the site location is deeper that completely curing time will be postpone, especially it is not easy to come into contact with air. if the temperature is low, cure time also will be postpone .Prior to further processing or wrapping the bonded parts, it is recommended that the user wait long enough to ensure that the adhesion and integrity of the adhesion are not affected.
Note: After the operation is completed, the unused glue should be tightened immediately and sealed. When used again, if the seal has a little bit of skin, remove it. In the process of storage, a small amount of curing phenomenon may occur in the pipe mouth, which can be used normally unaffected the product performance.
|
Our services |
|
1. 10 years TIMs experiences |
|
2. Professional R&D team |
|
3. One-stop service for thermal conductive material |
|
4. Support customized orders,including size,shape,color, and thermal conductivity or can be coated one side or two sides adhesive or fiberglass according to your demands |
|
5. Free sample provided |
|
6. Manufacturer offers best price |
|
7. Good quality and fast delivery |
|
8. Professional after-sale service |
|
9. Quality system to obtain ISO9001 certification,products meet ROHS,REACH and safety standard certification standards |
|
10. Prompt response within 24 hours |
Q1: What's the thermal conductivity test method given on the data sheet ?
A1: All the data in the sheet are tested out by the third party. ASTM D5470 is utilized to test the thermal conductivity.
Q2: How to find a right thermal conductivity for my application ?
A2: It depends on the watts of power source , ability of heat dissipation .
Q3: Do you accept custom orders ?
A3: Yes , welcome to custom orders. Our custom elements including dimension , shape , color and coated on side or two sides adhesive or coated fiberglass. If you want to place a custom order , pls kindly offer a drawing or leave your custom order information .
Q4: Do you offer free samples ?
A4: Yes, we are willing to offer free sample but pls kindly note that your side pay for freight .
Q5: How to ship the orders ?
A5: We will help to arrange transportation for you . If you want to use your own courier account pls kindly tell us before shipping out.
Q6: What's the leading time ?
A6: Sample order costs 1~3 workdays and 3~7 workdays for mass production.
- Step 1Find your interested products by search keywords
- Step 2Contact the supplier by clicking ”Enquire” or “request meeting” button, otherwise, you also could consult our import consultant.
- Step 3After verifying your email, get response from suppliers or our trade manager will contact you as soon as possible
- Step 4Set up meeting with the Chinese supplier without language barrier