Every DIY CNC amateur has a craftsman spirit or on the way to be a craftsman,our Artsoft Mach3 CNC 3/4/5/6 axis USB interface motion control interface controller can not say how perfect it is,but our team has been trying to create a craftsman spirit good product, thank you for your attention!
1. Support all version Artsoft MACH3 Software,include the current latest version.
2. Support all Windows system version,include Windows XP/7/8/10
3. It does not need any USB drive,plug and play in any windows system platform,hotplug also.
4. The USB bus adopt high grade chip to achieve the magnetic decoupling isolation,the real worth isolation,it is diiferent from the Optical coupling isolation input and output of the general motion controller,it achieve the super reliability and also absolutely keep the PC USB interface safety,guarantee the strong EMC anti-interference ability at the same time.
5. Single-core solution,simple system design compared to muti-chips system,what many times stability compared to multi-chips processing method.
6. Dual-core high speed CPU(the frequency of the single-core can reach 204MHZ),has great redundancy processing capacity.it can promise 500KHz pulse output under 4-axis linkage motion,300KHz pulse output under 6-axis linkage motion,optional to connect stepper/servo motor.
7. Motion control buffer size can be set,so it can keep the fastest interpolation cycle and smoothly run,even under the too heavy of the computer,it can also keep the smoothly run.
8. There are 16 isolation inputs,simple interfaces to connect conveniently,also support dry/wet connection,the dry connection method just needs to connect one external mechanism switch to the ground.All 16 inputs has each LED indicator,the LED indicator will illume when the signal is low level,it is easy to debug and check.
9. There are 12 outputs at most(4 isolation outputs and 4 non-isolation outputs).there are 12 outputs when it is 4-axis artsoft Mach3 controller.there are 8 outputs when it is 6-axis artsoft Mach3 controller.
10. Isolated PWM adjustable speed output,the PWM frequency can be set,and the duty cycle 0~1000 can be set continuously,support servo spindle,the pulse frequency can reach 800KHz.
11. Has the spindle speed detection function,the real speed of the spindle can real-time display in Mach3 sceen,the measurement is precise and stable.
12. The PCB is meticulously designed by the professional and experience engineer,the design level is clear at a glance.
13. Equip with 256KB NVRAM space,it can save 6 axis coordinates,so it does not need to seek for origin point on the next time power up.
About how to install Mach3 and our Artsoftware Mach3 3/4/5/6 axis motion controller applied in cnc machine vedio information and datasheet.
Pls feel free to ask for the share information and vedio link from us.
Already integrate USB isolating circuit,unlike the ordinary Mach3 CNC controller does not have,if the anti-interference can not fit your project,it needs another external USB isolating board,not stable and also add cost.
24V DC to 5 V DC power isolation module,input voltage range 18 to 36 V DC, 5VDC 6w power output.It can also supply 4 W power output at least except the board system use up 1.5W.
Single-Chip Dual-Core 32bit MCU,What many times performance it is compared to similar products,simple design so more reliable system.
Use Bidirectional Optocoupler,it can be applied to both NPN and PNP type sensor inputs,welcome to the Electronic peer to check,this is real isolation,the ground layout is separated,No copper and go lines in the middle!Every inputs has LED indicator, convenient to debug and check.
NVRAM battery installed base,it can save mechanism coordinates and processing line number.
Isolating outputs,it can be applied in controlling the FWD/REV direction of the inverter and other strong interference control signals.
PWM adopt 10M high speed isolating Optocoupler, and there are 5V/10V analog voltage select function.
10M high speed isolating Optocoupler as well,it can catch higher frequency pulse signal,and send this signal to the seeking for origin input,it can be applied in spindle thread tapping function.
The handwheel interface is independent,it does not occupy any inputs,the handwheel has independent Emergency Stop input IN17.
The general extension interface has RS232 and SPI interface,it will add external circuit as offline function.
2 analog signal inputs,it can connect one potentiometer to control the feedrate ratio and spindle speed ratio,it also can be used as detecting external sensors.
Convenient to wire
There is one capacitor still not in the picture,fully 5pcs tantalum capacitors,plus another 2pcs inductance, Fully considering the circuit stability
13. Various Protection
a) Self-recovery and over voltage protection for power input.
b) Pressure sensitive resistance protection inputs,it can prevent bad surge or static shock to break the circuit effectively.
c) Output series one 22R resistance ,it can protect ouput driver chip function when the output current is too big.
d) Encoder interface add input buffer chip,it can filter high frequency noise interference,and protect the static electricity break the interface at the same time.
e) 5V linear power output has self-recovery fuse(PPTC)(This 5V linear power is from the 24V DC supply linear power)
f) Output digital 5V (Digital isolating power supply output)
A: Yes,please feel free to contact with us,we will send our products specification,datasheet and test vedio to you.
A: Yes, we welcome sample order to test and check quality. We will provide the technical support. but if you does not have any basic knowledge,we do not suggest.
A:Sample needs 3-5 days, mass production time needs 2-4 weeks for order quantity.
A: Firstly after you check our controller datasheet or you are familiar with the Mach3 controller,you can directly tell us how many axis you need or you can let us know your requirements or application and how many axis you need.
Secondly We quote according to your requirements or our suggestions.
Thirdly customer confirms and send the payment to us.
Fourthly We arrange the delivery.
A: Firstly, Our products are produced in strict quality control system and the defective rate will be less
than 0.2%.
Secondly, we can provide the technical support and suggestions for your project,you just needs to have the basic electronic knowledge,we can give you support and we also provide the datasheet and vedio for your modification.