Nutshce Filter Dryer from TOPTION can make the material in a closed container equipment to complete the three process of filtration, washing and drying, to maximize the utilization of equipment. To avoid the pollution of the environment and also to avoid the pollution of the environment on the material to reduce the loss of material transport, saving solvent usage, suitable for batch mass production.
Nutsche filter dryer are widely used for critical high purity separations of liquids and solids, and now being used in the cbd oil industry.
It is widely used for final step of cbd oil purity process. With pur critical operation as final step, the cbd crystalizing isolation can reach above 98%
Name | DN600 Nutsche filter dryer | ||||
Item No | RFCD-DN600-316L | ||||
Container Diameter | 600mm | thickness | 6mm | ||
Filter Area | 0.28m2 | Volume | 0.2m3(200liter) | ||
Design Pressure | 0.4Mpa for container | 0.5Mpa for jacket | |||
Design Temperature | 130℃ for container | 150℃ for jacket | |||
Material | material-contacting parts:SS31603; Others: SS30408 | ||||
Filter type | 316L sintering net | Micron size | 10 micron | ||
Main Shaft seal way | Packing seal way | Material | PTFE packing | ||
Agitation blade | S-shaped asymmetric paddle | ||||
Shaft lift height | 100mm | ||||
Mixing stroke | 200mm | ||||
Explosion proof grade | dⅡBT4 | ||||
Stirring motor power | 1.5kw EX Motor | ||||
Stirring speed | 0~20r/min | ||||
Stirring lift type | Hydraulic Cylinder Drive | ||||
Chassis lift type | Hydraulic Cylinder Drive | ||||
Discharge port switch form | Hydraulic Cylinder and Hydraulic Motor Drive | ||||
Hydraulic motor power | 1.5kw |
Feature
1. Feeding
Open the feeding valve to feed in the tank, paddle should be in the upper position when feeding, if necessary, can be lowered stirring paddle for low speed stirring, so that the material is evenly distributed. When the material reaches the specified process stop feeding, close the feed valve
2. Washing
Washing fluid at 0.2 ~ 0.3MPa pressure by the rotating nozzle cleaning, and stirring paddle has been suspended high.
Slurry washing: When a certain amount of washing liquid after the accession to stop adding gradually lower stirring paddle and pulp slurry at an appropriate speed stirring. Stir continuously from top to bottom.
3. Filter
After washing, upper the stirrer to related position, stop stirring, the liquid will be discharged from bottom. Then repeat the filtering steps until you get perfect material.
If filter finish,make the material is similiar, then make the stirrer blade upper from material surface about 20mm.
4.Drying
1. open hot water valve, then balance valve, nextly vacuum valve.
2. Pls open the balance valve in advance if upper vacuum down drying condition, to ensure pressure balance. to Concentration of chloride ions in the heating and cooling water should be strictly controlled, to avoid chloride ions on the jacket and the tank corrosion. Pls use of chloride-free water.
3. Open the jacket water inlet valve slowly, and open slightly for water outlet valve. Fully open them when outlet and inlet has temperature gap less than 20℃ to avoid cavitation vibration.
5. Material discharge
Sampling analysis before discharge, if ok, then discharge them.
First turn off the heating water valve, slowly open the cooling water valve. Slowly lower the stirring paddle, stirring material accelerated cooling, then the vacuum pump can be opened to exhaust heat. Before open the discharge valve, pls fill pure nitrogen for balance protection. when the pressure is atmospheric pressure, the impeller through the thrust reverser action, the material discharged from the discharge valve.
-Standard wooden case.
-Both neutral and customized packaging can be available.
-We can ship the goods to you by International Express such as DHL,UPS,TNT,EMS and so on, you can also choose the appropriate one based on your timeline and budget. Besides,you can choose to use your own forward.
Q: What is your MOQ?
A:1 set.
Q: How long is your delivery time?
A: Generally it is within 3 working days after receiving the payment if the goods are in stock. Or it is 5-10 working days if the goods are not in stock, depending on order quantity.
Q: How to choose suitable equipment ?
A:tell us your Working speed and Maximum capacity ,then we will recommend you suitable equipment according to yourrequirements, application experience and feedback from our clients.
Q: How to solve the equipment trouble during using ?
A: Please email us about problem with pictures or a small video will be better,we will find the problem and solve it. If broken, we will send you a new free part if in the warranty period.