TOP 1 KONNWEI Factory Battery Load Tester for all 12V cars Digital car diagnostic analyzer battery tester with printer

KW210 battery tester key functions & features:

1.System voltage: 12 Volts

2.Test Result: Good, Recharge or Replace

3.Capacity - Cold Cranking Amps

(CCA), DIN, EN and IEC information relative to battery rating.

4.Internal resistance value (mΩ)

5.Life in percentage (%)

6.Cranking system

7.Charging system

8.Voltage test in waveform

9.Record and re-play battery data, Life-time free update service

10.Battery test, cranking test, charging test and other additional functions.

Specifications and Support Languages:

1.Measure Standard

2.CCA:100-2000

3.BCI:100-2000

4.CA:100-2000

5.MCA:100-2000

6.JIS:26A17-24SH52

7.DIN:100-1400

8.IEC:100-1400

9.EN:100-2000

10SAE:100-2000

11.GB:100-1400

12Display: Color TFT LCD Screen

13.System Voltage:12 Volts

14.Input Voltage Range:8V-16V

15.Power Requirements: No internal batteries required.

16.Power on when hooked up during testing.

17.Operating Temperature:0℃-50℃

18.Storage Temperature:-20℃-70℃

Application:

Use a test a wide range of 12v batteries(Starting{SLI},Deep Cycled and Marine) of Wet(Flooded),VRLA or Maintenance Free (MF),Sealed Maintenance Free (SMF), Absorption Glass Mat(AGM),EFB and GEL Cell.

The major battery standards CA,CCA,BCL,MCA,JIS,SAE,EN,GB,DIN and IEC are supported.

Package includes:

1*KONNWEI KW210 Auto Diagnostic Scanner

1*Mini USB cable

1*User’s Manual

(1) Battery Test

   Select the battery test and press OK key to continue:

   Battery Type: select your battery type, usually is “Regular Flooded”

   Input testing standard: the standard which you can see the front of the battery,such as CCA,BCI,DIN.

   If you can’t find any info about the standard, you can choose GB standard. Choose GB standards would lead little tolerance.

  Input rated capacity: you can see the starting current standards in front of the battery .Such as BCI/300A.

  Then press OK key to start testing.

Note:

For power loss battery (such as a vehicle for a long time on hold, the battery is not charged in time; 

forget to close the lights, the doors resulting in serious loss of battery electric vehicle and can not be started, etc.), 

in the actual testing process may also be prompted to "Please replace the battery," for such batteries, 

please consult the battery manufacturers, and then tested.

(2)Cranking Test 

Starting the engine as prompted, tester will automatically complete the cranking test and display the result. 

Normally, cranking voltage value lower than 9.6V is regarded as abnormal and it is OK if it is higher than 9.6V. 

Test result of the tester includes actual cranking voltage and actual cranking time.

When cranking test is abnormal, battery test result will also be displayed at the same time. 

(3)Charging Test

When enter the charging test, tester will prompt "Loaded testing" 

Note: Do not shut down the engine during the test. All electrical appliance and device are in OFF state. 

Turn on/off any electrical appliance in the vehicle during the test will affect the accuracy of the test result.

Operate accordingly to increase the engine rotating speed to 2500turns, and keep for 5 seconds. 

Tester starts the charging volt test after increase rev detected.

After the test finished, tester displays the effective charging volts, ripple test result and charging test result. 

Charging Test Result:

1. Charging Volt: Normal. The generator output normal, no problem detected.

2. Charging Volt: Low. Check drive belt of the generator whether slip or running off. 

Check the connection between generator and battery is normal or not. 

If both of the drive belt and the connection are in good condition, 

follow the manufacturer's suggestion to eliminate generator fault.

3. Charging Volt: High. Since most of the vehicle generators are using internal regulator, 

the generator assembly has to be replaced.(Some old style cars are using external regulator, then directly replace the regulator.) 

The normal high volt of the voltage regulator is maximum 14.7±0.5V.If charging volt is too high, 

it will overcharge the battery. Therefore, the battery life will be shortened and troubles will be caused.

4. No Volt Output. No generator volt output is detected. 

Check the generator connection cable, the drive belt of generator and engine whether normal or not.

5. Diode Test: Through the test of charging current ripple, tester will find out whether the diode is normal or not. 

When ripple volt is too high, it proves at least one diode is damaged. Check and replace the diode.

(4)Review Data

After entering the forth function, then press OK key you can view the final test result.

(5)Print Data

About Printing function, please contact with customer service.

(6)Export Data

Contact this battery tester to computer with Data Line, 

you can download the print software from our web. If any questions, please contact us.

More type , pls click here :

Hot sell KONNWEI KW600 car battery tester with printer and upgrade system free/ Auto Battery Analyzer For All 12V Cars