Dynamic classifier
Feed size: ≤0.5mm [Production capacity]: 10-60t/h
Application field
Cement grinding, new materials, dry mortar, ceramics, rubber, electricity, oil extraction, aerospace, etc.
Model |
Processing capacity |
Air volume |
Rotating speed |
Oil pump |
Motor power |
motor model |
(t/h) | (m3/h) | rpm | (kw) | |||
MX200A | 4-8 | 10000-14000 | 300-600 | SGZ-8 | 11 | Y160L-4 |
MX350A | 8-12 | 21000-24000 | 200-500 | SGZ-8 | 15 | Y160L-4 |
MX500A | 14-16 | 24000-36000 | 200-400 | SGZ-8 | 18.5 | Y180L-4 |
MX700A | 21-24 | 36000-48000 | 200-350 | SGZ-8 | 22 | Y180L-4 |
MX850A | 26-34 | 48000-55000 | 200-300 | SGZ-8 | 30 | Y200L-4 |
MX1000A | 34-42 | 55000-70000 | 150-300 | SGZ-8 | 37 | Y225L-4 |
MX1500A | 43-52 | 80000-110000 | 150-300 |
SGZ-8 |
45 |
Y250L-4 |
Applicable material
Cement, pulverized coal, calcium-based powder, silicon micropowder, titanium dioxide, silica powder, iron ore, quartz stone, construction waste, gold ore, etc.
Outstanding advantages
MX series coal mill dynamic powder sorting machine is a high-performance selection of a new generation of coarse powder separation and horizontal vortex powder sorting based on the introduction, digestion and absorption of foreign wind sweeping coal mill special dynamic classifier Powder machine.
1. Large output and wide working conditions
Adopting advanced structure, the powder volume and output can be changed freely within a large range without affecting the efficiency of powder selection, and the system output is increased by 10%-15%.
2. The equipment has low resistance and high efficiency and energy saving.
The uniform flow field optimization design has higher powder selection efficiency, less equipment resistance and obvious energy saving effect.
3, easy to operate, easy to adjust fineness
The main motor of the classifier can be remotely controlled, and the main motor speed can be adjusted to meet different fineness requirements.
4. Low wear and low maintenance costs.
A new eddy current dispersing device is installed inside, the airflow in the rotor rises without rotating, the momentum moment reduces the driving force on the rotor, saves the driving power, reduces the wear force, and the wearable parts are treated with wear-resistant materials and processes.
working principle:
The air discharged from the coal mill enters the classifier with the material from the lower air duct, and is rectified by the inner cone to decelerate along the annular
passage between the outer cones. The coarse powder is slipped along the outer cone side wall by gravity settlement. Into the coarse powder receiving cylinder to achieve gravity sorting. The air after gravity separation forms a stable horizontal vortex particle separation zone between the guide vane and the rotor under the action of the guide vanes of the guide vanes and the rotation of the rotor. The dust particles moving in the eddy current will be affected by gravity, wind and centrifugal force. The small and slight particles will be sucked into the rotor through the air outlet pipe with the airflow, and then collected into the dust to be separated as the finished fine powder. The coarse and heavy particles are dropped, collected into the coarse powder collecting cylinder through the inner cone, and returned to the mill for re-grinding. Changing the rotor speed can effectively adjust the fineness of the finished product.
Case 1 :35TPH fly ash production line
Equipment:
2.6×13m ball mill + YF450 powder separator in Vietnam
Case 2 :20 TPH fly ash production line in Laos
Equipment:
2.4×10m ball mill + YF300 Air Classifier
Case 3 :60 TPH fly ash production line in Russia
Equipment:
2 SET 2.4×10m ball mill +2SET YF450 powder separator
Case 4 :15TPH fly ash production line in Brazil
Equipment:
2.0×10m ball mill + YF250 powder separator
Case 5 :20TPH fly ash production line+ 300TPHCrushed stone production line in Hashakstein
Equipment: 300TPH crusher plant + YF300 powder separator
Case 6 :25TPH fly ash production line in Guangxi
Equipment:
YF300 powder separator
Case 7 :55TPH fly ash production line in China
Equipment:
YF500 powder separator
Q: Hi, are you mining machinery manufacturer?
A: Yes, our company warmly welcome clients to visit our plant at any time. We can also provide samples test, mine design, equipment manufacture, after-sale service, etc…
Q: Which country have your products been exported?
A: We have been exported business for 10 years and we have lots of customers and agents in the world, such as Middle East, Malaysia, South Africa, Canada, America, etc…
Q: How long is the warranty of your equipment? Does your company supply the spare parts?
A: The usual warranty period is one year. And of course, we will supply the spare parts for you at lowest cost.
Q: If I need the complete mineral processing line, can you help us to build it?
A: Yes, we can help you combine a complete mineral processing line and give you related professional advices as long as you need. We had already build many mining projects in China & Overseas. We can set a complete processing line just as you require.
Ways of Packing:
1.Sand blasting, coat with high quality paint;
2.Product wrap by PP-Bubble
3.Load container, Spear Parts in wooden case.
Transportation:
1. By sea Freight;
2. MSK/MSC/APL/EMC/WANHAI/KLINE
3. We will remind you before boat arrival
YINGYONG is able to produce large piece or manufacture according to requirements: rotary kiln up to 6m, grinding mill up to 5*16m, our bending machine could bend up to 6m and thickness 120mm, casting piece could be up to 24t net weight, equipments could treat all kinds of pieces up to 8m and 80t weight, hobbing machine up to 8m.