Anaerobic Jar AG Series

DESCRIPTION

AG series anaerobic jar can be used with 2.5L AnaeroGen/CampyGen/Microaerobic sachet. It also can be fitted with MARK or DWS A05050 anaerobic system.

FEATURES:  1. No catalyst required.

                           2. Polycarbonate base which is secured to the lid by four clips. These clips are designed to allow                                               venting in the  unlikely event of a positive pressure build-up occurring i.e. by allowing lid to lift                                        and reseal to maintain correct condition.

                           3. Vacuum relief screw to overcome any vacuum which may occasionally occur.

                           4. It can choose two different connectors to fit with all kinds of anaerobic system or flow with

                                gas.

Tank: transparent high-temperature resistant polypropylene material injection molding, high strength, high temperature resistance, high thermal conductivity

Temperature resistance: can withstand no more than 100C high temperature Sealing: good sealing performance, anaerobic holding time not less than 120 hours

Locking: unique four-button seal design, simple operation, convenient, can be individually replaced lock, low maintenance costs

Can lid: 3 standard fitting holes are configured. Can be fitted with a connector to connect various anaerobic culture systems,

Use as a vent hole.

Material: The tank body and cover are made of transparent high-strength polyester material, high finish, shock and shock resistance

Temperature resistance: can withstand temperature 50C

Sealing: It is fixed by the clamp and fully sealed.

Material: stainless steel (SUS304), durable, good thermal conductivity Temperature resistance: Can be resistant to 121C high temperature sterilization

Seal: Stainless steel lock seal, good sealing performance

Number of locks: 3

Product size: 19.7*13.5*9.5cm

Volume : 10 discs (diameter 90mm) max, 

           10. Remove jar after the appropriate incubation time and open lid by carefully depressing                        the clips to release the jar lid from base. Excessive downward pressure on the clips                              should beavoided.

    11. Occasionally a slight vacuum may occur after anaerobiosis producing a negative pressure,           resulting in resistance to the removal of the lid (after release of clips). This is overcome              by screwing and turning anticlockwise allowing inlet of air. It is important, however, to                ensure the valve is resealed by turning clockwise prior to further use.

Method 2: evacuate and fill with gas

1. Insert the carrier in the jar.

2. Place an anaerobiosis indicator in the jar.

3. Close the lid.

4. Connect the vacuum pump with a thick-walled hose to the connector.

        5. Connect a gas bottle containing the requested gas mixture to the another connector.                    The pressure reduction valve is to set to max. 0.1 bar over pressure at the outside.

6. Open the valve connector with the pump and extract the gas from the jar.

7. Close the valve connector with the pump and open the valve connected with gas bottle.

8. Fill the jar with requested gas mixture up to 0.1 bar.

        9. Depending on the sensitivity of the microorganisms, the process of evacuation and filling             with gas may be repeated once or twice.

10. After the last filling with gas, close both valves and remove the               hoses.

11.Transport the jar to the incubator.

Method 3:flow with gas

1. Insert the carrier in the jar.

2. Place an anaerobiosis indicator in the jar.

3. Close the lid.

         4. Connect a gas bottle containing the requested gas mixture to the connector. The                 pressure reduction valve is to set to max. 0.1 bar over pressure at the outside.

5. Open both two valve connector.

6. Open the gas supply and flow the jar with the requested gasmixture.

7. Flow  the jar with requested gas mixture up to 0.1 bar overpressure.

8. Depending on the sensitivity of the microorganisms, the jar may be flowed from 5 to 15minutes.

    9. After the last flowing with gas, close both valves and remove the               hoses.

    10.Transport the jar to the incubator.

PRECAUTION

The jar should not be autoclaved. It is not suitable incubator exceeding 80 celsius.

CLEANING AND DISINFECTION

Disposable gloves should be worn throughout the following operations.

The Anaerobic jar only be wiped with alcohol as longer residence times may expand the material and cause cracks.

MSL is a professional supplier of the Medical Equipment. Our company is located at Guangzhou.

We specialize in various ultrasound machine, including the portable ultrasound machine, trolley ultrasound machine, wireless ultrasound probes with 11 years experiences for domestic market, 7 years for export. Do you want to know more about our products? Please free feel to contact Vera.

Please rest assure that our superior quality will make you or your customers very satisfied. We give reference to you for our satisfied customers scattered all over world like Britain, America, Canada,Japan, Italy, Saudi Arabia, Cyprus and other countries. Therefore, we have great confident that our products could meet your different requirements.

Top 3 Alibaba Trade Assurance Supplier, Factory Direct Selling Price,Professional Service Team, In-time After-Sales Service Deserve Your Order.