Pneumatic 50/25T Heavy Duty 50 Tons Air Hydraulic Floor Jack Long Ram For Truck
Pneumatic 50/25T Heavy Duty 50 Tons Air Hydraulic Floor Jack Long Ram For Truck
50 ton hydraulic jack
1)Hydraulic floor jack is ideal for car&truck repair and tire change and garage use.
2)Our hydraulic floor jack's quality meet or exceed ANSI/CE requirements.
3)Hydraulic floor jack's bypass device protects against over-pumping for safer operation.
4)Built-in safty valve provides overload control.
5)Heavy-duty steel construction provides long term durability.
6)Large steel caster and swivel casters for easy maneuverability.
7)Light weight for easy mobility and transport.
8)All welded steel frame construction with cast iron support arms with rust resistant finish for long tool life.
| Model | Capacity (T) | Minimum height (mm) | Lift height (mm) | Extension height (mm) | Weight (kg) |
| AU-50 | 50(Signle Node) | 192 | 307 | 30mm 70mm | 46 |
| AU-50 | 50/25(Double Node) | 195 | 400 | 30mm 70mm | 59 |
| AU-50 | 50/25(Double Node) | 160 | 315 | 30mm 70mm | 50 |
| AU-80 | 80/40(Double Node) | 195 | 400 | 30mm 70mm | 59 |
| AU-80 | 80/40(Double Node) | 160 | 315 | 30mm 70mm | 50 |
| AU-100 | 100/50(Double Node) | 200 | 430 | 30mm 70mm | 69 |
| AU-120 | 120/60(Double Node) | 192 | 398 | 30mm 70mm | 78 |
1 .How to Choose Pneumatic Hydraulic Jack?
According to the vehicle chassis to choose Pneumaitc Hydraulic Jack Model.
Buses and electric vehicles chassis lower the jack need to choose lower height.
Truck chassics highter so its need to choose the higher height jack.
According to Vehicles self wight to choose the Pneumatic Hydraulic Jack Model.
Bus is usually a few tons or a dozen tons,and a 30ton jack is usually enough,If want to increase the used time can choose hig more capacit
2. What about Pneumatic Hydraulic Jack Ranges?
The Pneumatic Hydraulic Jack is a new type of hydraulic lifting equipment which combines pneumatic liquid turbo-charged with telescopic hydraulic cylinder.It has advantge including exquisite design,small volume,light weight,easy operstion,low labor intensity,high work efficiency,big lifting tonnage and so on.It is widely used for liquidity lifting,especially for automobiles and tractors in transportation industry.
The pneumatic Hydraulic Jack is only used in flat and upright position ,not in side or upside down position.The operating temperature ranges from -20°Cto 50°C.It can not be used in PH or corrosive gas places.
3. How about the Pneumatic Hydraulic Jack Slope Test?
The Slope experiments has not been done and there is no accurate numerical description.When tilted to how many degrees,it will cause the pulling cylinder.Domestic requirements are to use it on a flat and vertical ground.The design of the cooper belt was designed fot the anti-tension cylinder at the beginning.It will not pull the cylinder when the slope is larger,But it will be biased when the slope is large,which is also unfavorable to the quipments. The Jack must be used vertically on a flat and solid ground.The roofcan not be tilted.The ground is uneven,the ground is soft and the tilted roof.Overloading is illegal.It is easy to crack the base or pull the inside of the cylinder.Id the strain is not visible to the naked eye,the cylinder head must be disassembled and inspecte.
4. How about The Role of Pressure limiting Valve with Pneumatic Hydraulic Jack?
The External Pressure of the air pimp is very large,which causes the base cylinder to deform.To protect the quipments,we added a pressure limiting valve,When the external pressure is too large,the excess pressure will be removerd when passing the pressure limiting valve to protect the product.
5. What is your terms of delivery?
EXW, FOB, CFR, CIF, DDU
6. How long is the Warranty for the Pneumatic Hydraulic Jack?
We provided 12months quality assurance.
7. How about the delivery time?
Usually our producing time is 15-20days after we receive the advanced payment, and if we have the stock, we could delivery immediately.
8.Can you provide customized products? OEM products or ODM products?
Yes, we can provide customized products per your request, both OEM and ODM are acceptable. We do a lots of non-standard products.
9.Could we request our own color for the products?
Yes, of course, you just need to offer us the RAL code.
Pre-Sales Service
* Inquiry and consulting support.
* Photos&Videos for your order before shipment.
* View our Factory.
After-Sales Service
* Training how to instal the machine, training how to use the machine.
* Whole life-time supply for spareparts.
- Step 1Find your interested products by search keywords
- Step 2Contact the supplier by clicking ”Enquire” or “request meeting” button, otherwise, you also could consult our import consultant.
- Step 3After verifying your email, get response from suppliers or our trade manager will contact you as soon as possible
- Step 4Set up meeting with the Chinese supplier without language barrier