Parameters of Model M200 | ||||||||
Working area of one fin | 0.92(㎡) | |||||||
Type of product | 1.0Mpa | 1.6Mpa | ||||||
Designed pressure | 1.0Mpa | 1.6Mpa | ||||||
Testing pressure | 1.3Mpa | 2.1Mpa | ||||||
Designed temperature | -55℃~+230℃ | |||||||
Max.flowrate at the water side | 600m³/h | |||||||
Number of fins in the maximun assembly | 398PCS | |||||||
Type of fin passage | D、X、H | |||||||
Materials of fin | 304、316L |
GPHE Features | |||||
High Heat Transfer Efficiency | When the media flowing through the plates in a lower Reynold number, it can create turbulence, moreover, the smooth plates is not easy to generate scaling, so that the system has very high heat transfer efficiency in general water-to-water heat exchange process, this system’s heat transfer efficiency can achieve as high as 5000w/㎡.k which is higher than tubular heat exchanger by 204 times | ||||
Due to high exchanging efficiency, the heat transfer temperature can be very low, it’s best for lower-heat energy recycle. Generally, the heat recovering rate of plate heat exchanger is up to 90%. | |||||
For plates can be organized for different courses, plate heat exchanger could be designed to its optimal point and to flexibly suit the heat load changes without changing the frame, rest is only need to changing the plate number to suit new conditions, | |||||
Low retention volume due to the small channel, therefor plate heat exchanger is good at controlling the temperature and reduce the weight of the devices, especially for heat sensitive material processing. | |||||
The space occupied by plate heat exchanger is less than others. Under the same conditions, the space of plate heat exchanger is 1/3 or ¼ of tubular heat exchanger and it doesn’t need extra room during maintenance. | |||||
The plate can be cleaned in site, due to there is no dead end on it. The arrangement of course channel, the inlet and outlet of the eclectic media of heat exchanging fixed on the constant plate. This design is helpful cause no need to knock down the channel during cleaning. |
GPHE Model | ||||||||||||||||
Model | A (mm) | W (mm) | H (mm) | W1 (mm) | H1 (mm) | Max Tubing (mm) | Max Plate (Pcs) | Max Flow (m³/h) | ||||||||
M30 | N(2.0+X) | 180 | 480 | 60 | 356 | 32 | 80 | 15 | ||||||||
MH60B | N(2.0+X) | 320 | 920 | 140 | 640 | 50 | 250 | 36 | ||||||||
MH60H | N(3.0+X) | 320 | 920 | 140 | 640 | 50 | 203 | 36 | ||||||||
MH100B | N(2.55+X) | 470 | 1069 | 225 | 719 | 100 | 278 | 140 | ||||||||
MH100H | N(3.95+X) | 470 | 1069 | 225 | 719 | 100 | 180 | 140 | ||||||||
MH150B | N(2.5+X) | 610 | 1815 | 298 | 1294 | 150 | 600 | 360 | ||||||||
MH150H | N(3.95+X) | 610 | 1815 | 298 | 1294 | 150 | 600 | 360 | ||||||||
MH200H | N(4.0+X) | 780 | 2160 | 353 | 1478 | 200 | 398 | 600 | ||||||||
MH250H | N(3.5+X) | 920 | 2698 | 439 | 1939 | 250 | 300 | 795 | ||||||||
P50 | N(2.4+X) | 300 | 678 | 126 | 394 | 50 | 200 | 36 | ||||||||
P150 | N(4.0+X) | 608 | 1425 | 296 | 890 | 150 | 300 | 360 | ||||||||
T200 | N(4.0+X) | 740 | 1460 | 363 | 698 | 200 | 300 | 600 | ||||||||
X as Plate thickness |
Plate Material | Applicable Fluid |
Stainless Steel | Clean water, river water, cooking oil, mineral oil |
Ti, Ti-Pd | Sea water, salty water, salinization compounds |
20Cr, 18Ni, SMO | Dilute sulphuric acid, inorganic acids |
Ni | High temperature, High concentrations of caustic soda |
Hastelloy (C276, D205, B2G) | Cconcentrated sulphuric acid, hydrochloric acid, phosphoric acid |
Gasket Material | Usage Temperature | Applicable Fluid | ||||
NBR | -15℃ ~ +135℃ | Water, sea water, mineral oil, salty water | ||||
EPDM | -25℃ ~ +180℃ | Hot water, steam, acid, alkali | ||||
F26 | -55℃ ~ +230℃ | Acid, alkali, fluids | ||||
FTP | 0℃ ~ +160℃ | Cconcentrated acid, alkali, steam, high temperature oil |
Each Plate Contains 2 Parts | ||
Metal Plate | Produced into different patterns based on different working conditions to ensure the best heat transfer efficiency | |
Rubber Gasket | Fixed in the gasket slot around plate edge to seal the plates so that the medium flow can be formed |
Gasket Connection Type | ||
Glued Type | Heat curing 2 liquid bonding agent, to achieve high adhesive force, good seal ability, waterproof, good tensile strength, good stability. | |
Clip-on Type | Insert the jump ring into the plate slot and fix it, easy to remove and replace, reduce the maintenance cost and time. |