TI CC2652P Multi-protocol module BLE5.1 TI CC2652P ZigBee module
RF-BM-2652P2 is an RF module based on TI lower-power CC2652P SoC, which is a multiprotocol 2.4 GHz wireless module supporting Thread, Zigbee®, BLE® 5.1, IEEE 802.15.4, IPv6-enabled smart objects (6LoWPAN), proprietary systems, including the TI 15.4-Stack (2.4 GHz), and concurrent multiprotocol through a Dynamic Multiprotocol Manager (DMM) driver. It integrates a 48 MHz crystal and a 32.768 kHz crystal, 352 KB of in-system Programmable Flash, 256 KB ROM, 8 KB of Cache SRAM, 80 KB of ultra-low leakage SRAM. Its ARM® Cortex®-M4F core application processor can operate at an extremely low current at flexible power modes. And the module enables long-range and low-power applications using integrated +20 dBm high-power amplifier with best-in-class transmit current consumption at 85 mA. It features small size, robust connection distance, and rigid reliability.
RF-star can provide customers with the integration of the entire profiles, applications, radio and BLE protocol stack. With compliance to BLE standard, the RF-star’s modules enable the creation of a new market for tiny, cost-effective and power-efficient wireless consumer products such as watches, medical sensors, mice, TV remote controls and fitness trainers.
Parameters of RF-BM-2652P2
Chipset |
CC2652P |
Supply Power Voltage |
1.8 V ~ 3.8 V, 3.3 V is recommended |
Frequency |
2402 MHz ~ 2480 MHz |
Maximum Transmit Power |
+20.0 dBm |
Receiving Sensitivity |
-100 dBm @ 802.15.4 (2.4 GHz) -105 dBm @ Bluetooth 125 kbps (LE Coded PHY) |
GPIO |
23 |
Power Consumption |
RX current: 6.9 mA TX current: 7.3 mA @ 0 dBm 9.6 mA @ 5 dBm 22 mA @ 10 dBm 85 mA @ dBm MCU 48 MHz (CoreMark):3.4 mA (71 μA/MHz) Sensor Controller:30.1 μA @ Low Power-Mode, 2 MHz, running infinite loop 808 μA @ Active-Mode, 24 MHz, running infinite loop Standby: 0.94 µA Shutdown: 150 nA |
Support Protocol |
BLE 5.1, ZigBee, Thread, IEEE 802.15.4, 6LoWPAN |
Crystal |
48 MHz, 32.768 kHz |
Package |
SMT packaging (Half hole) |
Communication Interface |
UART, SPI, I2C, I2S |
Dimension |
30.0 mm × 16.4 mm × (2.2 ± 0.1) mm |
Type of Antenna |
PCB antenna, IPEX connector antenna, half-hole antenna interface |
Operating Temperature |
-40 ℃ ~ +85 ℃ |
Storage Temperature |
-40 ℃ ~ +125 ℃ |
Pin Diagram of RF-BM-2652P2
Pin |
Name |
Chip Pin |
Function |
Description |
1 |
DIO5 |
DIO5 |
GPIO |
GPIO, Sensor Controller, high-drive capability |
2 |
DIO6 |
DIO6 |
GPIO |
GPIO, Sensor Controller, high-drive capability |
3 |
DIO7 |
DIO7 |
GPIO |
GPIO, Sensor Controller, high-drive capability |
4 |
DIO8 |
DIO8 |
GPIO |
GPIO |
5 |
DIO9 |
DIO9 |
GPIO |
GPIO |
6 |
DIO10 |
DIO10 |
GPIO |
GPIO |
7 |
DIO11 |
DIO11 |
GPIO |
GPIO |
8 |
DIO12 |
DIO12 |
GPIO |
GPIO |
9 |
DIO13 |
DIO13 |
GPIO |
GPIO |
10 |
RES |
RESET_N |
RES |
Reset, active lo. No internal pullup resistor. |
11 |
JTAG_TMSC |
TMSC |
JTAG_TMSC |
JTAG TMSC, high-drive capability |
12 |
JTAG_TCKC |
TCKC |
JTAG_TCKC |
JTAG TCKC |
13 |
VCC |
EXT_3V3 |
VCC |
Power supply: 1.8 V ~ 3.8 V, 3.3 V re recommended. |
14 |
GND |
GND |
GND |
Ground |
15 |
DIO14 |
DIO14 |
GPIO |
GPIO |
16 |
DIO15 |
DIO15 |
GPIO |
GPIO |
17 |
DIO16 |
DIO16 |
GPIO |
GPIO, JTAG_TDO, high-drive capability |
18 |
DIO17 |
DIO17 |
GPIO |
GPIO, JTAG_TDI, high-drive capability |
19 |
DIO18 |
DIO18 |
GPIO |
GPIO |
20 |
DIO19 |
DIO19 |
GPIO |
GPIO |
21 |
DIO20 |
DIO20 |
GPIO |
GPIO |
22 |
DIO21 |
DIO21 |
GPIO |
GPIO |
23 |
DIO22 |
DIO22 |
GPIO |
GPIO |
24 |
DIO23 |
DIO23 |
GPIO or Analog |
GPIO, analog capability |
25 |
DIO24 |
DIO24 |
GPIO or Analog |
GPIO, analog capability |
26 |
DIO25 |
DIO25 |
GPIO or Analog |
GPIO, analog capability |
27 |
DIO26 |
DIO26 |
GPIO or Analog |
GPIO, analog capability |
28 |
DIO27 |
DIO27 |
GPIO or Analog |
GPIO, analog capability |
29 |
GND |
GND |
- |
Ground |
30 |
ANT |
- |
ANT |
Antenna |