HST-I Parameter: | ||||||||||||||
Model | Speed ratio | Enter the rated torque at 2000r/min | Allowed peak torque at start stop | The allowable maximum of the average load torque | ||||||||||
NM | kgfm | NM | kgfm | NM | kgfm | |||||||||
14 | 50 | 6.2 | 0.6 | 20.7 | 2.1 | 7.9 | 0.7 | |||||||
80 | 9 | 0.9 | 27 | 2.7 | 12.7 | 1.3 | ||||||||
100 | 9 | 0.9 | 32 | 3.3 | 12.7 | 1.3 | ||||||||
17 | 50 | 18.4 | 1.9 | 39 | 4 | 29.9 | 3 | |||||||
80 | 25.3 | 2.6 | 49.5 | 5 | 31 | 3.2 | ||||||||
100 | 27.6 | 2.8 | 62 | 6.3 | 45 | 4.6 | ||||||||
20 | 50 | 28.8 | 2.9 | 64.4 | 6.6 | 39 | 4 | |||||||
80 | 39.1 | 4 | 85 | 8.8 | 54 | 5.5 | ||||||||
100 | 46 | 4.7 | 94.3 | 9.6 | 56 | 5.8 | ||||||||
120 | 46 | 4.7 | 100 | 10.2 | 56 | 5.8 | ||||||||
160 | 46 | 4.7 | 100 | 10.2 | 56 | 5.8 | ||||||||
25 | 50 | 44.9 | 4.6 | 113 | 11.5 | 63 | 6.5 | |||||||
80 | 72.5 | 7.4 | 158 | 16.1 | 100 | 10.2 | ||||||||
100 | 77.1 | 7.9 | 181 | 18.4 | 124 | 12.7 | ||||||||
120 | 77.1 | 7.9 | 192 | 19.6 | 124 | 12.7 | ||||||||
32 | 50 | 87.4 | 8.9 | 248 | 25.3 | 124 | 12.7 | |||||||
80 | 135.7 | 13.8 | 350 | 35.6 | 192 | 19.6 | ||||||||
100 | 157.6 | 16.1 | 383 | 39.1 | 248 | 25.3 | ||||||||
40 | 100 | 308 | 37.2 | 660 | 67 | 432 | 44 |
Maximum torque is allowed in an instant | Allow the maximum speed to be entered | Average input speed is allowed | Back gap | Design life | ||
NM | kgfm | r / min | r / min | Arc sec | Hour | |
40.3 | 4.1 | 7000 | 3000 | ≤30 | 10000 | |
54.1 | 5.5 | |||||
62.1 | 6.3 | |||||
80.5 | 8.2 | 6500 | 3000 | ≤30 | 15000 | |
100.1 | 10.2 | |||||
124.2 | 12.7 | |||||
112.7 | 11.5 | 5600 | 3000 | ≤30 | 15000 | |
146.1 | 14.9 | |||||
169.1 | 17.2 | |||||
169.1 | 17.2 | |||||
169.1 | 17.2 | |||||
213.9 | 21.8 | 4800 | 3000 | ≤30 | 15000 | |
293.3 | 29.9 | |||||
326.6 | 33.3 | |||||
349.6 | 35.6 | |||||
439 | 44.8 | 4000 | 3000 | ≤30 | 15000 | |
653 | 66.6 | |||||
744 | 75.9 | |||||
1232 | 126.7 | 4000 | 3000 | ≤30 | 15000 |