Product Introduction
CIM-3115RMT(A) Magnet Analyzer is a high precision automatic measuring device for measurements of the magnetic field strength on the surface of magnets with four axial position. It adopts PC+ARM double layer control, and adds module design based on CIM-3110RMT which is suitable for high end market. It can automatically test the peak value, angle, area, width and FWHM of every pole; automatically judge the poles number of magnet ring and the polarity of them; statistic analysis of test results and calculate the maximum, minimum, average and standard deviation of every parameter; it can draw the X-Y curve, polar coordinates curve and three dimensional curve.
By changing the fixing method of probe and fixture of sample, the system can support several test modes of hard magnets, such as internal and outside surface, upper surface, Z axes linear, cylindrical surface, round surface and surface scanning. It can multidimensional automatic scan of the surface magnetism of samples, and visually observe the surface magnetic field distribution of sample by graph, which is a valuable implement for assessment and optimization of magnetic components.
Measurement and control module
1, LZ-652 Gaussmeter
Accuracy: superior to 0.50%
2, LZ-700 Motion controller
Single axes control: max 5 axes control(W axes has curve speed up and down control function)
Sensor: max 15 groups of sensor
Interface: RS232 or CCTALK bus communication
3, LZ-100 Data processor
Sampling: 4 channel 24 bit ADC sampling, communication total rate highest 50Khz;
Communication interface: Ethernet data communication interface;
CCtalk total communication and slave control, slave automatic identify;
Pulse sampling function;
Command code decoding function;
Product Structure
The instrument automatic self-inspection of hardware after power on, with the LCD to display the instrument state, at the same time, XYZ axes automatic back to the zero point, to ensure the consistency of probe position when testing.
W axes adopts precision electric rotary platform, by the drive of stepper motor to control the rotary angle of sample, and the angular resolution is 0.01°. When measure circular samples, adopt high precision 3-jaw self-centering chuck for precision positioning ,the concentricity is superior to 0.05mm.
The chuck has the nickel plating to avoid the corrosion which was caused by humid environment and oxidation.
The jaw is made of non-magnetic materials, to avoid the effect of measured results which is caused by the magnetic conductive of fixture.
There is a couple of sensors in the middle of platform, which can roughly check the outer diameter of sample and check whether there is sample fixed in the platform, to effectively avoid damage of machine which is caused by faulty operation.
Hall probe positioning mechanism
The hall probe coated with the aluminum alloy post for effectively make sure the strength and perpendicularity of it.
There are positioning slot both on probe fixed block and probe handle, to make sure the position consistency.
There is also anti-collision mechanism, when there is force on the vertical direction, the instrument will automatically stop test and the probe automatically restoration.
Software interface
1, XY coordinate curve
2, Polar coordinate curve
3, Three-dimensional coordinate curve
4, Three-dimensional cylinder curve
5, Cylinder unfold curve
HUNAN LINKJOIN TECHNOLOGY CO., LTD. warrants each instrument of its manufacture to be free from defects in material and workmanship. Our obligation under this warranty is limited to servicing or adjusting any instrument returned to our factory for that purpose. The warranty period is 18 months. On returning the equipment under warranty, the buyer bears the costs for the shipment to LINKJOIN; LINKJOIN bears the costs for returning the device to the buyer. However, the buyer bears all the costs for shipment, taxes and duties, if the device is returned to LINKJOIN from abroad.
The warranty period begins on the date of delivery of the product or later on the date of installation of the product if the product is installed by LINKJOIN, the warranty period begins on the 31st day after delivery, provided that if you schedule or delay the LINKJOIN installation for more than 30 days after delivery.
LINKJOIN warrants the product only if it has been sold by an authorized LINKJOIN employee, sales representative, dealer or LINKJOIN headquarter.
The warranty period does not apply to defects of product result from improper or inadequate maintenance, repair or calibration;unauthorized modification or misuse; improper site preparation or maintenance. Caution: the hall probe is easy to damage; it's not in the warranty scope list.
1. 100% Manufacture
Both our factory and company are founded in Loudi, Hunan Province. We are specialized in manufacture and
sales of magnetic measurement instruments. All the products are made by our own factory. So our price is
competitive.
2. Quality control
From the material to the final product. All the components together with production procedure are inspected
and controlled. We ensure the products have been fully inspected by our QC one by one before shipment.
3. Reliable after sales service
Free training for the operation of equipment in our company, which is provided by our professional training
department.
We provide 18months warranty for the maintenance without charges for components change or repairing.
(except for fragile parts) . And we are responsible for lifelong repair, and charge appropriately for repair
service out of warranty period.