LB-JZX Welding Smoke Eater and Laser Fume Extractor for Metal cutting fume Master and Dust Collector

LB-JZX Welding Smoke Eater /Portable Fume Extractor, Fume Master and Dust Collector for welding 

Qingdao Loobo portable fume extractors are mainly used to extract/collect the fume and dust in the metal fabrication process, like the welding, polishing, grinding, metal cutting, etc. it can be moved freely to the fume source place.

With active carbon filter layer, some odor gas can be absorbed before released the clean air. Portable type with small size, you can move them freely in your workshop to the working posation, economic and high efficiency.

Available for both one arm and double arms.

LB-JZX Series welding fume extractor Parameters Table:

All the models are designed with Pulsing back-flushing automatic dust-removal system. " S " respresents the welding fume extractor has the double arms for two working stations.

Back-flushing pressure is 0.5-0.6Mpa.

Voltage can be other type, 3p and 1p are available.

  LB-JZX back-flushing pressure is 0.5-0.6Mpa.

The welding fume extractor/ purifier is easy of installation, and has no technical requirements when the customer install and use it. The flexible extraction arm is made from high quality material of PVC and steel wire, which is anti-corrosion, heat-resistant of up to 140°C. It can swivel 360º and can be brought in any desired direction without additional support. It is equipped with the damper to adjust the wind. It is equipped with the caster wheels and can be freely mobile to meet the requirements of different work places.

The purified gas can meet the standard requirements and can enter into work room or indoor place, which is helpful to keep the room close, maintain the temperature and be convenient for work.

Operating Principle:

Under the help of the fan device, the welding fume is sucked into inlet through multi-direction sucking hood. There is the flame arrester in the inlet, so the spark can be blocked here, and the left fume and dust is sucked into gravity separator. The bigger paticiles firstly descend into dust bag. The smaller particles is arrested in the surface of core filter. The cleaner gas then flow into clean room after being purified by core filter. In clean room, the clean gas is then further purified by active carbon. At last, the gas meets the required standards and enter into air or other required room.

The BasicStage Filtration Process about the SMOKE EATER

Stage 1: Air passes trhough  the pre-filter fire-proof net. 
Stage 2: Air passes through a second pre-separator to further reduce medium to heavy particulate matter. 
Stage 3: Air passes through the LongLife-H filter where welding fume particles are captured and deposited. 
Stage 4: Activated carbon filter will help prevent or neutralize the release of odors back into the environment. 

Facility Characteristics 

1)      It is equipped with ABB turbo fan and motor imported from Germany and America, with overload prevention circle to avoid motor damage. It is of steady performance.

2)      It is equipped with built-in centralized PLC controlling system. The operation panel is clear and simple, very easy to operate.

3)      Pulsing back-flushing automatic dust-removal system: The filter core is the automatic rotating and back-flushing type, which keeps the filter core surface clean when working, to insure the stable blowing rate; The air compressor parts are connected with high pressure rubber pipe with high pressure air-inflow in the bottom, which insure the facility always in good working condition.

4) The filter core is imported from the large company in America with long useful life. It can arrest the 0.3μm particles. The filtering effect is good for all kinds of particles including the wet particles.

5) It is equipped with the all-directions sucking arm of 360 degree rotating. It can suck the fume exactly from the source which make best of the fume collection efficiency, and insure the workers’ health in the largest extent.

6) It is equipped with three layer filter system to avoid the damage effect of flame and large slag particles, which extend the useful life, more safe and more reliable.

7) The clean air is exhausted uniformly and diffusely through the gridiron outlet, so it can minimize the noise.

8) It is attached with all-direction caster wheels, which makes the facility movable freely and easy to position.

9) Photoelectric controlled on/off, energy saving and high efficiency. The hood has the lighting device which is upon customer’s choice.

10) The parts working condition are all stable and has long useful life, meantime easy to be replaced.

Custom design and production for the welding fume extractor is available.

Other main welding fume extractors:

1. LB-JZ model(economic type welding fume collectors, single arm or double arms, manual cleaning or auto reverse pulse jet cleaning type):

LB-JZ Series Welding Fume Purifier Parameters Table, Maunal cleaning type:

LB-JZ Series Welding Fume Purifier Parameters Table, Auto cleaning type:

The " D " in models for the welding fume extractors represent Pulsing back-flushing automatic dust-removal system. " S " respresents the welding fume extractor has the double  arms for two working stations. 

2.LB-BG model(wall mounted welding fume extractor filtration type):

3.LB-JK model(with simple structure cartridge filter big airflow welding dust purifer ):

4.LB-JW model( HEPA High Efficiency two grade filter Welding Smoke Extractor):

5.LB-JF model(High vacuum pressure with low airflow robot welding dust absorber):

Components used on the welding Smoke eaters

Shipping for the welding fume extractors:

Company press:

We,Qingdao Loobo Environmental Protection Technology Co.,Ltd is aimed to air purifying and kinds of removing fume exhausted,  with its own R&D team more than ten years manufacturer, located in Qingdao city of china, specialized in the main products:

1,portable welding fume extractors,and soldering fume extractors etc.,

2.downdraft benches(grinding dust removal worktable),

3.central fume purification projects,

4.Spare parts:flexible suction arm,etc.

All of our products with the ISO9001, and CE certification for parts of products, the quality can be guaranteed.

 ATTN: Miss Molly Huang