The common rechargeable batteries include lithium batteries, nickel cadmium batteries, nickel hydrogen batteries, and sealed lead-acid batteries. Among them, lithium battery has the characteristics of large capacity, light weight and high cycle times. It is widely used in mobile phones, PDA, digital cameras, camcorders, notebook computers and other fields.Is currently the most advanced rechargeable battery, referred to here is the finished lithium battery lithium battery pack by lithium batteries (lithium ion batteries or Li polymer batteries) and lithium battery protection board. Nickel cadmium battery is a relatively early application of rechargeable battery. It has the characteristics of low cost, low internal resistance and high current discharge. So far, it has been widely applied in some electric tools and electric cars.
Similar NiMH battery and nickel cadmium battery, but because they do not contain heavy metals, so the environmental pollution is small, at present in some common consumer electronic products have been widely applied in fields of application, has replaced the previous nickel cadmium batteries. Small sealed lead-acid battery, also known as maintenance free lead-acid electric he, at present mature technology, mainly used in fixed backup power applications, such as uninterruptible power supply, emergency lighting and so on.
In view of the requirements for the production and detection of these rechargeable batteries, a special integrated battery tester for rechargeable batteries has been developed.This tester can make a quantitative and accurate measurement of some basic parameters of the battery.The open circuit voltage, internal resistance,charging, discharge performance of the battery can be measured,Battery capacity is especially aimed at the function of lithium battery. It also has the functions of charging protection, over discharge protection, over current protection, short circuit protection, etc., and has measured the corresponding value, which greatly facilitates the production and pre-sale and after-sales service of battery.A few simple steps can be used to intuitively judge the performance and quality of the battery.At the same time, it also has the function of quick screening. It can set the upper and lower limits of measurement parameters. It can quickly detect the bad battery from a batch of battery products and improve the production efficiency. In addition, some special functions have been added to enable them to have some characteristics of universal instruments and equipment, expand the flexibility of the equipment, and have a wide range of applications.
Besides, this tester can provide software upgrade services according to the needs of customers. On the basis of basic models, it can upgrade to software that can be connected to computers based on basic models, and can set up and save test data by computer, and automatically record test resultsThe battery bar code can also be used to record the test data of each battery, which is beneficial to the analysis and control of production quality, the recovery of the products, and so on.In addition, the test accuracy of voltage and resistance can be increased by an order of magnitude by adding a hardware upgrade module to meet the more stringent quality requirements.
The basic functions of the JK5530 battery comprehensive tester include:
1.The static parameters of the battery are detected quickly.
1.1 Battery voltage detection (for a lithium battery that has been in a protected state, it can automatically wake up)
1.2 Battery internal resistance detection
1.3 Battery charge performance detection
1.4 Detection of battery discharge performance
1.5 Detection of battery overcurrent size (only for lithium batteries)
1.6 Detection of battery short circuit protection function (only for lithium battery)
1.7 The above can be detected in the part of the value size, and the upper and lower limits can be set to be screened quickly.
2.Battery capacity detection.
3.The battery charging function can be selected separately.
4.The battery discharge function can be selected separately.
5.The function of the numerical control current and voltage source.
6.Numerical control electronic load function.
7.Function of voltage and internal resistance meter
8.Instrument calibration function
Instrument characteristic index:
Model | JK5530 | JK5530B | ||||
measuring range | Range of battery voltage measurement | 0-36V,Minimum resolution 10mV,accuracy:±30mV | 0-60V,Minimum resolution 10mV,accuracy:±5mV | |||
| Range of internal resistance measurement | 0-999mΩ,Minimum resolution 1mΩ | 0-1999mΩ,Minimum resolution 1mΩ | |||
| Capacity measurement range | 0-10000mAH,Minimum resolution 1mAH | ||||
measurement accuracy | Accuracy of voltage measurement | 60V:±0.05%(After calibration) | ||||
| Accuracy of current measurement | 5A:±2% 10A:2% | ||||
| Accuracy of internal resistance measurement | 150mΩ:5% | ||||
| Accuracy of battery capacity measurement | 10AH :±5% | 100AH :±5% | |||
Test speed | Static test (test all functions) | 1.1-2 seconds | ||||
| Capacity test (1C current charge and discharge) | 3-4 hours | ||||
Internal numerical control voltage source index | Maximum output voltage | 16V | 62V | |||
| Maximum output current | 5A | ||||
| Maximum output power | 80W | 200W | |||
| Ripple voltage | <20mV | ||||
| Load adjustment rate | <10% | ||||
| response time | 1S | ||||
Internal numerical control electronic load index | Ceiling voltage | 60V | 80V | |||
| Maximum discharge current | 10A (continuity),15A(10 second) | 30A(continuity) 40A(2 second),60A( Need to be customized) | |||
| Limit power | 50W(continuity),80W(10 second) | 200W (continuity) | |||
| supply voltage | 220V±10%50Hz | ||||
U disk storage |
| no | yes | |||
communication interface |
| no | yes(with Host computer software) | |||
Accessories |
| Kelvin clip test line, test probe | ||||
Size and weight |
| Upper frame size (mm):215(w)*88(H)*375(D) |
FAQ
A: Payment Terms:
T/T, Western Union, Paypal, Bank Transfer
B: Shipment:
1. By EMS, DHL, FedEx, TNT, UPS or other express.
2. By your own forwarding agent.
3. Buyer can choose the desired shipping method when ordering.
C: After-sale service:
All products have been checked and packaged in good condition before dispatch.
D: Lead Time:
After the payment, general orders will be delivered from our factory within 3-5 working days.
Customers Service
Please contact us through email or phone, we will assist you in any way possible
China working hours 9:30-18:30 Monday-Friday online service to help buyers solving problem.
Welcome the friends from all over the world to visit us !