Welcome to TradeChina
Industrial slurry sludge silica sand clay drum dryer machine price, energy saving small mini triple pass cement rotary dryer
FOB Reference Price
Purchase quantity ()
Minimum order quantity
Payment
Meo Textile Clothing Co.LTD
China - Hangzhou
Manufacturer
Trade Capacity
Export Percentage
Nearest Port
shanghai,ningbo
Accepted Delivery Terms
Employees
101-200 people
Accepted Payment Currency
USD,CNY
Average Lead Time
60 Day(s)
Certifications
Product Specifications
Model Number
VS0.8x8
Product Description
Product Overview
Sludge/Coal Slime Drying System
Material Description：
Sludge refers to the sediment produced by dealing with waste water through the physical,
chemical, biological methods, according to their sources, which can be divided into electroplating sludge, printing and dyeing sludge, tanning sludge, paper sludge, pharmaceutical sludge, sewage sludge, living sewage sludge and petrochemical sludge, etc.
Because of its features of poor mobility, high viscosity, easy to agglomerate, and the water is not easy to evaporate and so on, it’s very hard to dry, and the high drying technology is required (the drying technology of this drying system is also adopted to dry the coal slime, gypsum and other similar wet sticky materials).
chemical, biological methods, according to their sources, which can be divided into electroplating sludge, printing and dyeing sludge, tanning sludge, paper sludge, pharmaceutical sludge, sewage sludge, living sewage sludge and petrochemical sludge, etc.
Because of its features of poor mobility, high viscosity, easy to agglomerate, and the water is not easy to evaporate and so on, it’s very hard to dry, and the high drying technology is required (the drying technology of this drying system is also adopted to dry the coal slime, gypsum and other similar wet sticky materials).
System Description：
With the continuous enhance of people's awareness of environmental protection, and sludge drying technology is also in the rapid development, the constant innovation and improvement also happens in the aspects of energy saving, safety, reliability, sustainability. Our company sludge drying system is going to reduce the water content of dewatered sludge from 80 + 10% to 20 +10%. The advantages of our system are as follows:
1.The weight of the dried sludge can be reduced to 1/4 weight of wet material before drying, which greatly reduces the enterprise's environmental and economic pressure.
With the continuous enhance of people's awareness of environmental protection, and sludge drying technology is also in the rapid development, the constant innovation and improvement also happens in the aspects of energy saving, safety, reliability, sustainability. Our company sludge drying system is going to reduce the water content of dewatered sludge from 80 + 10% to 20 +10%. The advantages of our system are as follows:
1.The weight of the dried sludge can be reduced to 1/4 weight of wet material before drying, which greatly reduces the enterprise's environmental and economic pressure.
2.The air inlet temperature of the dryer is 600-800℃, and it can be used for sterilization, deodorant, etc. at the same time of drying, and reliable guarantee will be provided for the utilization of dried products;
3.The dried products can be used as feed stuff, fertilizer, fuel, building materials, raw materials for extracting heavy metals,to realize waste utilization.
FEATURES AT A GLANCE
The dewatered sludge will be transported to feeding head of the dryer through the screw conveyor after scattering, and then it will be sent into the inside of the dryer through the unpowered spiral sealing feeder (the patent technology of our company), and going through several following working areas after getting into the dryer:
1. Material leading-in area
The sludge will come into contact with the high temperature negative pressure air after getting into this area and plenty of water will be rapidly evaporated, and the sludge can’t be formed into sticky stuff under the stirring of large guide angle lifting plate.
2. Cleaning area.
The material curtain will be formed while the sludge is lifted up at this area, and it will cause the material stick on the cylinder wall while it’s falling down, and the cleaning device is installed at this area (Lifting style stirring plate, X type second time stirring plate, impacting chain, impacting plate), the sludge can be quickly removed from the cylinder wall by the cleaning device, and the cleaning device can also crush the materials which are bonded together, so as to increase the heat exchange area, increase the time of heat exchange, avoid the generation of wind tunnel phenomenon, improve the drying rate;
3. Inclined lifting plate area
This area is the low temperature drying area, the slime of this area is at the low moisture and loose state, and there is no adhesion phenomenon at this area, the finished products reach the moisture requirements after the heat exchange, and then enter the final discharge area;
4. Discharging area
There aren’t stirring plates at this area of the dryer cylinder, and the material will be rolling to the discharging port.
The sludge gradually becomes loose after drying, and discharged from the discharging end, and then sent to the designated position
by the conveying device, and the fine dust drawn out along with the tail gas is collected by the dust collector.
Hot air enters into the drying machine from the feeding end, and the temperature is gradually reduced at the same time of material
convection heat transfer, and the water steam taken out under the suction of induced draft fan, and then emitted into the air
after processing.
1. Material leading-in area
The sludge will come into contact with the high temperature negative pressure air after getting into this area and plenty of water will be rapidly evaporated, and the sludge can’t be formed into sticky stuff under the stirring of large guide angle lifting plate.
2. Cleaning area.
The material curtain will be formed while the sludge is lifted up at this area, and it will cause the material stick on the cylinder wall while it’s falling down, and the cleaning device is installed at this area (Lifting style stirring plate, X type second time stirring plate, impacting chain, impacting plate), the sludge can be quickly removed from the cylinder wall by the cleaning device, and the cleaning device can also crush the materials which are bonded together, so as to increase the heat exchange area, increase the time of heat exchange, avoid the generation of wind tunnel phenomenon, improve the drying rate;
3. Inclined lifting plate area
This area is the low temperature drying area, the slime of this area is at the low moisture and loose state, and there is no adhesion phenomenon at this area, the finished products reach the moisture requirements after the heat exchange, and then enter the final discharge area;
4. Discharging area
There aren’t stirring plates at this area of the dryer cylinder, and the material will be rolling to the discharging port.
The sludge gradually becomes loose after drying, and discharged from the discharging end, and then sent to the designated position
by the conveying device, and the fine dust drawn out along with the tail gas is collected by the dust collector.
Hot air enters into the drying machine from the feeding end, and the temperature is gradually reduced at the same time of material
convection heat transfer, and the water steam taken out under the suction of induced draft fan, and then emitted into the air
after processing.
Projects
PRODUCT SPECIFICATIONS
Model | Cylinder diameter (mm) | Cylinder length (mm) | Cylinder volume (m3) | Cylinder rotary speed (r/min) | Power (kW) | Weight (t) |
VS0.6x5.8 | 600 | 5800 | 1.7 | 1-8 | 3 | 2.9 |
VS0.8x8 | 800 | 8000 | 4 | 1-8 | 4 | 3.5 |
VS1x10 | 1000 | 10000 | 7.9 | 1-8 | 5.5 | 6.8 |
VS1.2x5.8 | 1200 | 5800 | 6.8 | 1-6 | 5.5 | 6.7 |
VS1.2x8 | 1200 | 8000 | 9 | 1-6 | 5.5 | 8.5 |
VS1.2x10 | 1200 | 10000 | 11 | 1-6 | 7.5 | 10.7 |
VS1.2x11.8 | 1200 | 11800 | 13 | 1-6 | 7.5 | 12.3 |
VS1.5x8 | 1500 | 8000 | 14 | 1-5 | 11 | 14.8 |
VS1.5x10 | 1500 | 10000 | 17.7 | 1-5 | 11 | 16 |
VS1.5x11.8 | 1500 | 11800 | 21 | 1-5 | 15 | 17.5 |
VS1.5x15 | 1500 | 15000 | 26.5 | 1-5 | 15 | 19.2 |
VS1.8x10 | 1800 | 10000 | 25.5 | 1-5 | 15 | 18.1 |
VS1.8x11.8 | 1800 | 11800 | 30 | 1-5 | 18.5 | 20.7 |
VS1.8x15 | 1800 | 15000 | 38 | 1-5 | 18.5 | 26.3 |
VS1.8x18 | 1800 | 18000 | 45.8 | 1-5 | 22 | 31.2 |
VS2x11.8 | 2000 | 11800 | 37 | 1-4 | 18.5 | 28.2 |
VS2x15 | 2000 | 15000 | 47 | 1-4 | 22 | 33.2 |
VS2x18 | 2000 | 18000 | 56.5 | 1-4 | 22 | 39.7 |
VS2x20 | 2000 | 20000 | 62.8 | 1-4 | 22 | 44.9 |
VS2.2x11.8 | 2200 | 11800 | 44.8 | 1-4 | 22 | 30.5 |
VS2.2x15 | 2200 | 15000 | 53 | 1-4 | 30 | 36.2 |
VS2.2x18 | 2200 | 18000 | 68 | 1-4 | 30 | 43.3 |
VS2.2x20 | 2200 | 20000 | 76 | 1-4 | 30 | 48.8 |
VS2.4x15 | 2400 | 15000 | 68 | 1-4 | 30 | 43.7 |
VS2.4x18 | 2400 | 18000 | 81 | 1-4 | 37 | 53 |
VS2.4x20 | 2400 | 20000 | 91 | 1-4 | 37 | 60.5 |
VS2.4x23.6 | 2400 | 23600 | 109 | 1-4 | 45 | 69.8 |
VS2.8x18 | 2800 | 18000 | 111 | 1-3 | 45 | 62 |
VS2.8x20 | 2800 | 20000 | 123 | 1-3 | 55 | 65 |
VS2.8x23.6 | 2800 | 23600 | 148 | 1-3 | 55 | 70 |
VS2.8x28 | 2800 | 28000 | 172 | 1-3 | 75 | 75 |
VS3x20 | 3000 | 20000 | 141 | 1-3 | 55 | 75 |
VS3x23.6 | 3000 | 23600 | 170 | 1-3 | 75 | 85 |
VS3x28 | 3000 | 28000 | 198 | 1-3 | 90 | 91 |
VS3.2x23.6 | 3200 | 23600 | 193 | 1-3 | 90 | 112 |
VS3.2x32 | 3200 | 32000 | 257 | 1-3 | 110 | 129 |
VS3.6x36 | 3600 | 36000 | 366 | 1-3 | 132 | 164 |
VS3.8x36 | 3800 | 36000 | 408 | 1-3 | 160 | 187 |
VS4x36 | 4000 | 36000 | 452 | 1-3 | 160 | 195 |
PRODUCT CONFIGURATION
SALES AND SERVICE NETWORK
Packing and Shipping
No desirable products?
Sourcing assistant>
How to start your business
- Step 1Find your interested products by search keywords
- Step 2Contact the supplier by clicking ”Enquire” or “request meeting” button, otherwise, you also could consult our import consultant.
- Step 3After verifying your email, get response from suppliers or our trade manager will contact you as soon as possible
- Step 4Set up meeting with the Chinese supplier without language barrier
Popular Searches
opel racing partstattoo machine partssoda machine partschemical tank heaterpopcorn machine partschemical dosing skiddigging machine partshss machine tapsicecream machine factorymidea washing machine partssiruba 747 machine partssplicer machine yarnmini washing machine partsplastic sealing machine partsdaewoo washing machine partshino marine partschemical fiber canvaschemical lace overlaysex machine partsdahao embroidery machine partsbola machine ballschemical mixing vatssewing machine gearfuji machine partslima crane partschemical resistant pantsgerman alpine hatszenoah engine partshospital bassinet cartpitching machine partschip removal machine toolspower press machine partsship engine partschemical earthing systemsulzer machine partsedge banding machine partselna sewing machine parts0.0001mm machine partssurgical light partsamerican racing rims