Indoor grow room tools 8 burner co2 generator kit controller for plants

Calibration

Place the CO2 sensor outdoors if possible (or in a room with fresh air ventilation) and press both knobs simultaneously for 3 seconds until the display reads CAL / 400. If necessary, the calibration point can be adjusted by turning the CO2 PPM knob. Calibration begins automatically after five seconds. During calibration keep the sensor out of direct sunlight, away from sources of CO2, and be sure to not breath on the sensor. Allow 10 minutes for the calibration process to complete and stabilize the CO2 reading. The display will stop flashing the PPM value once the calibration process is complete.

Note about Calibration: The PPM-B1 is factory calibrated, but to ensure precise readings and optimal control it is recommended to place the sensor outside for a period of ten minutes to test, after which the displayed PPM value should be around 400 (this value might be slightly higher in city environments compared to rural environments). In the unlikely event that your controller readings differ greatly from 400 PPM it is then X recommended to recalibrate the unit.

The CO2 Controller, with an adjustable CO2 set point and deadband, offers precise and accurate control of 240-volt CO2 supplementation devices. Utilizing the built in photocell feature this controller limits CO2 production to the light hours to maximize savings and increase yields. Featuring three control modes - PPM UP for CO2 generator use, FUZZY LOGIC for superior accuracy when utilizing a tank and regulator setup, and PPM DOWN if desired. ETL, CE, FCC approved for safety and dependability.

Specification:

1. Save these instructions. This safety and operating instructions must be kept in a safe place for future reference.

2. Heed all warnings. All warnings on this product and in the instructions must be observed closely.

3. Follow all instructions. All operating instructions must be followed.

4. If the instructions as provided by the manufacturer are not followed damage to the product may result.

5. Install your controller at least 8 ft away from any devices that produce large amounts of electronic noise, such as electronic ballasts or ozone generators.

6. The output voltages of this controller's receptacles are the same as the input voltage. The receptacles can only be used in conjunction with plug styles NEMA1-15P and NEMA 5-15P. DO NOT attempt to insert any other plug configuration into the controller receptacles.

7. DO NOT use this controller near a water source. The controller is not water-proof or shock-proof, and as such should not be exposed to direct water contact or extremely high moisture.

8. DO NOT attempt repair. Any factory serviceable parts of this controller are only to be repaired or replaced by the manufacturer or other authorized agencies.

9. If the power cable insulation is broken, please stop using the product. Immediately unplug the controller and contact the retailer from whom you purchased the unit.

10. The controller is equipped with a circuit breaker for short-circuit or over-current situations. The circuit breaker will automatically shut down the product at once. All outlets of the controller are grounded for safety.

11. Do not block any ventilation openings. This product is a Safety Class I Controller. The main plug should be inserted in a power socket outlet only if provided with a protective earth contact. Any interruption of the protective conductor inside or outside of the product is likely to make the product dangerous and is prohibited.

Weili Technology Co.,Ltd was established in 2014, the original factory of LED grow light. Ecospeed motto is "Quality matters, yield matters!" The company's area around has 15000sqm, over 200 staff, more than 15engineers ( 3 foreigners), and more than10patents by far now. All kinds of test machines are available. Ecospeed devotes itself to the development of the Future Eco-agriculture, your trusted LED Grow light and aquarium light supplier.

 Other Models

Advantages:

1. High Efficacy Up to 2.8-3.0 umol/J, High PPFD;

2. Fanless Design; 3. Aluminum Body with Great Heat Dissipation +Silicone Coating;

4. 3 Years Warranty+5 Years Extension with IP65 Waterproof Inventronics Driver;

5. ETL,DLC,CE,RoHS Certificates;

6.Optional for 480W/650w/720w;

7. Covering Full-cycle Growing Stages;

8. No Need Assemble, Two Times Foldable Design, All in One, Small Package, Easy to Install Plug and Play.

Features

1. Suitable for plants growth of all stages, full-spectrum, includes all useful wavelengths;

2. Energy saving over 40%, 1000w HPS replaced,15% yield increased!

3. Suitable for all moisture work environments with excellent waterproof design;

4. Full-spectrum 3000k+6500k+660nm+730nm/Custom Spectrum.OEM/ODM/ re-branded Logo/Package Available;

5. Optional for 2pcs UV bars working together with each setup(pls advise us if needed.)

6. Dimmable 0-10V/1-10V automatic/App/Wifi/computer remote control/5 dimming/RJ14 timer dimming control available;

Factory Price

Certification: DLC and ETL

Plant Cultivation

If you are a home tent grower, Show us your grow size and how many plants;

If you are a commercial grower, Show us the layout of the greenhouse;

Professional LED Grow Light Solution Will be Offered Accordingly.

* Ecospeed,7 floors.Around 15000 sqm. 200staff.over 4yrs experience in LED.Around 10 patent products.

* Ecospeed, Specializing in all kinds of LED grow lighting/ plant grow light.
* Ecospeed, Professional solutions will be offered, OEM/ODM is acceptable.
* Ecospeed, More than 15 engineers,3 foreigners are included.
* Ecospeed, All test equipment for LED lighting is available.

Q1. Can I have a sample order for led grow light?
A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.

Q2. What about the lead time?
A: Sample needs 3-5 days, mass production time needs 1-2 weeks for order quantity more than.

Q3. Do you have any MOQ limit for led grow light order?
A: Low MOQ, 1pc for sample checking is available.

Q4. How do you ship the goods and how long does it take to arrive?
A: We usually ship by DHL, UPS, FedEx or TNT. It usually takes 3-5 days to arrive. Airline and sea shipping also optional.

Q5. How to proceed an order for led grow light?
A: Firstly let us know your requirements or application.
Secondly We quote according to your requirements or our suggestions.
Thirdly customer confirms the samples and places deposit for formal order.
Fourthly We arrange the production.

Q6. Is it OK to print my logo on led grow light product?
A: Yes. Please inform us formally before our production and confirm the design firstly based on our sample.

Q7: Do you offer guarantee for the led grow light products?
A: Yes, we offer 2-5 years warranty to our products.

Q8: How to deal with the led grow light faulty?
A: Firstly, Our products are produced in a strict quality control system and the defective rate will be less than 0.2%.
Secondly, during the guarantee period, we will send new lights with new orders for a small quantity. For defective batch products, we will repair them and resend them to you or we can discuss the solution including re-call according to real situation.

Contact

Contact: Sophia Luo

What'sapp/Phone: +86 132 9719 9127

Company web: www.ecospeedled.com
Address: Baoan District,  Shenzhen, China 518104

Any questions & problems, welcome to contact us!