High Quality PC material ST41B Ceiling Mount PIR Infrared Human motion sensor
The product adopts good sensitivity detector and integrated circuit. It gathers automatism, convenience, safety, saving-energy and practical functions. It utilizes the infrared energy from human as control-signal source and it can start the load at once when one enters detection field. It can identify day and night automatically. It is easy to install and used widely.
Specifications:
Power Source: 110 -130V/AC 220 -240V/AC Detection Range: 360°
Power Frequency: 50/60Hz Detection Distance: 6m max(<24℃)
Ambient Light: <3-2000LUX (adjustable) Working Temperature: -20~+40℃
Time Delay: Min.10sec±3sec Working Humidity: <93%RH
Max.15min±2min Power Consumption: approx 0.5W
Installation Height: 2.2-4m Detection Moving Speed: 0.6-1.5m/s
Rated Load: 110 -130V/AC : 220 -240V/AC :
800W(incandescent lamp) 1200W(incandescent lamp)
200W(energy-saving lamp) 300W(energy-saving lamp)
Lifetime and Warranty:
Lifetime (hr) |
26000-45000 at least |
Warranty |
5 years |
FUNCTION:
Ø Can identify day and night: The consumer can adjust working state in different ambient light. It can work in the daytime and at night when it is adjusted on the “sun” position (max). It can work in the ambient light less than 3LUX when it is adjusted on the “3” position (min). As for the adjustment pattern, please refer to the testing pattern.
Ø Time-Delay is added continually: When it receives the second induction signals within the first induction, it will restart to time from the moment.
INSTALLATION ADVICE:
As the detector responds to changes in temperature, avoid the following situations:
Ø Avoid pointing the detector towards objects with highly reflective surfaces, such as mirrors etc.
Ø Avoid mounting the detector near heat sources, such as heating vents, air conditioning units, light etc.
Ø Avoid pointing the detector towards objects that may move in the wind, such as curtains, tall plants etc.
CONNECTION:
Ø Unload the transparent vinyl cover which is at the bottom of the sensor.
Ø Loose the screws in the connection terminal, and then connect the power to connection terminal of sensor according to connection-wire diagram.
Ø Install back the transparent vinyl cover into the original location.
Ø Fold the metal spring of the sensor upwards, until they are in “I” position with sensor, and then put the sensor into the hole or installation box which is on the ceiling and has the similar size with the sensor. Releasing the spring, the sensor will be set in this installation position.
Ø After finishing installing, turn on the power and then test it.
CONNECTION SKETCH FIGURE:(As per below drawing)
TEST:
Ø Turn the TIME knob anti-clockwise on the minimum (10s).Turn the LUX knob clockwise on the maximum (sun).
Switch on the power; the sensor and its connected lamp will have no signal at the beginning. After Warm-up 30sec, the sensor can start work .If the sensor receives the induction signal, the lamp will turn on. While there is no another induction signal any more, the load should stop working within 10sec±3sec and the lamp would turn off.
Ø Turn LUX knob anti-clockwise on the minimum (3). If the ambient light is more than 3LUX, the sensor would not work and the lamp stop working too. If the ambient light is less than 3LUX (darkness), the sensor would work. Under no induction signal condition, the sensor should stop working within 10sec±3sec.
Note: when testing in daylight, please turn LUX knob to (SUN) position, otherwise the sensor lamp could not work!
Our company adopts automatic machines, such as: SMD, auto component inserter, wave solder, autoinjection machines,the daily output is up to 20000-30000 pcs.
The concept of our company is"advocating new modern living environment",which focuses on researching and developing the contemporary household intelligent product.Our product can be truly satisfied for different customer's requirement,most of them are available with CE GS ROHS R&TTE REACH certification.