Performance parameters:
The 3kW foaming machine is a small cement foam generator. It is a special equipment specially used for producing foam in small factories. It is simple and convenient to operate. It is suitable for small factories, universities, colleges, scientific research institutes and other production departments to develop new products. It can also be used for medium-sized construction in decoration projects.
Usage and installation method:
Power connection: This equipment uses a three-phase 220V power supply. After all the lines are connected, click the start button, and then immediately click the stop button to check the direction of rotation. Make sure that the direction of rotation of the motor is correct. If the direction of rotation of the motor is incorrect, The two live wires need to be exchanged arbitrarily, and don't connect them wrongly.
Note: The panel voltmeter will display after the wiring is completed and the power is turned on. When the display voltage is normal at 220V, the air switch can be closed at this time, and the device enters the operational state.
Pipeline connection: Please connect the water pipe and foaming agent straw to the corresponding interface at the front of the device. use
Wrap the tape around the joint to prevent air leakage. If air leakage occurs, the foaming agent cannot be pumped or
Insufficient flow affects the efficiency of bubble making.
Bubble tube: The bubble tube is external and detachable. The front end of the bubble tube is detachable to replace the steel ball filled in the tube. The operation is simple, convenient and quick when disassembling.
Foaming machine models
Model |
Maximum flow |
Foaming speed |
Rated power |
Power |
Size |
Weight |
TR6 |
1.6KG/mim |
33L/mim |
600W |
220V |
60*40*40cm |
30kg |
TR15 |
10KG/mim |
120L/mim |
1.5KW |
220V |
75*49*65cm |
90kg |
TR30 |
5.5KG/m |
120L/mim |
3KW |
220V |
120*50*90cm |
120kg |
TR75 |
21KG/mim |
300L/mim |
7.5KW |
380V |
120*100*100cm |
300kg |
TR130 |
43.6KG/mim |
550L/mim |
13KW |
380V |
226*90*120cm |
500kg |
Usually need to be disassembled:
1. After working for a long time, it is found that the foam shape is not good, usually more than three months.
2. Pipe blockage: Some foaming agent remaining in the bubble tube will form a solid residue. In this case, the foam cannot be produced normally, or the pipeline pressure increases sharply. At this time, all the old steel balls need to be taken out, and then replaced with a new one The ball is fine. Steel wire ball specification requirements: each blowing tube needs to be filled with about 12-15 steel wire balls. Too much or too little will affect or even destroy the foam performance.
Precautions:
1. Remember to use electricity safely. If water or foam touches the circuit, you must immediately cut off the power at the remote end to ensure safe production.
2. There will be air in the pipeline when it is used for the first time. The foaming liquid has not been pumped into the equipment in a short time. You can wait for tens of seconds until the liquid is filled with the entire suction tube and the foaming operation can be performed normally.
3. Do not start the equipment when the pipeline is blocked to prevent damage to the components due to overpressure in the pipeline.
Luoyang Tongrun Info Technology Co., Ltd., the leading technology developer and application manufacturer of foaming agent, proudly announces their latest discovery which is centred towards the new ways for foam concrete, popular cement admixture developed by the company. It is suitable for Portland cement conventional foam concrete cast-in-place, block, sheet, and thermal insulation wall.
Foam Concrete are used in bridge approaches/embankments, pipeline Abandonment/annular fill, trench backfill, precast blocks, precast wall elements/panels, cast-in-situ/cast-in-place walls, insulating compensation laying, insulation floor screeds, insulation roof screeds, sunken portion filling, trench reinstatement, sub-base in highways, filling of hollow blocks, prefabricated insulation boards and much more.
Why Choose Us? Our Distinct Advantages:
1. Gold supplier and manufacturer*Our Target:We provide best quality products and very competitive price on the market. Our target is to build a long term business relationship with our customers.
* For all your inquires about us or our products, we will reply you in detail within 24 hours.
*Customize services are available when needed..
*After-Sale Service:For quality issues,we provide free tech-support and recommended formulations
Storage conditions
Concrete foam generator should be stored in dry, cool and sealing of the environment, can not be exposure to air, in addition should avoid the heavy pressure, according to ordinary goods transportation.