HPC015S Infrared counter wifi available toilet solution occupancy system connect LCD screen door counter for store

HPC015S infrared people counter (WIFI version) is small-sized and battery-powered. Parameter settings and data browsing can be done through a smartphone.

door counter door counter door counter door counter door counter door counter door counter door counter door counter door counter door counter door counter door counter door counter door counter door counter

Installation of Cover Plate

There is a cambered notch at the top of receiver and transmitter. Use the thumbs of both hands to press the cover plate and the base, then op

en the cover plate carefully. After the installation and settings are finished, the cover plate can be buckled on.

Attention!

Be sure to install the cover plates in correct direction.

The black bar area of the cover plate is infrared light transmission area. The infrared light of transmitter emits infrared ray beams through the area. Receiver receives the infrared ray beams and shows the contents of OLED display screen through the area.

After installing the battery, OLED display screen will show the booting information. By touching the touch sensor button, you can switch the contents on display screen: the current battery remaining capacity (BAT) and product serial number (SN), working parameters, open and close time, start AP menu and so on. If without touch operation for more than 10 seconds, the display screen will automatically turn off to reduce power consumption.

There are three indicator lights for receiver:

Red indicator light is used as the infrared focus indication. When receiver cannot receive the infrared signal from transmitter, the red indicator light will flash. Through this indicator light, you can easily find the suitable mounting position of transmitter.

Yellow indicator light is used for low-voltage battery alarm and charge indications. When the battery voltage is too low, the indicator light will flash to remind you to charge or replace the battery. When the battery is charged through the USB interface, the indicator light is on. If you do not want to use battery, turn the DIP switch of power supply mode to the "V" position, then you can use the USB interface to charge the receiver.

Blue indicator light is for WIFI network transmission or data saving indication.

Installation of Receiver

Receiver is installed on the right side of entrance in pedestrian’s entry direction. The USB interface of receiver faces down, and the infrared receiving units of receiver face the direction of transmitter. Use the matched double-sided tape to paste the receiver on the wall or door frame at about 1.3m height. If there is no suitable flat surface to fix the receiver directly in the installation location, you can use the matched mounting bracket to make sure the receiver and transmitter is face-to-face.

1. Display Screen Contents of Receiver

Touch the underface of the light bar (touch sensor button position) to wake up the OLED display screen. When the OLED display screen is light, the display contents will be switched every time you touch the OLED display screen. The below contents can be displayed respectively:

As the device is battery-powered, in order to maximize the battery life, the display screen will automatically turn off if without touch operation in 10 seconds.

2. Configuration of Receiver

You need to prepare a smartphone with WIFI function to complete the configuration.
Switch the contents of display screen to "Keep press to AP" interface, long press for 5 seconds until the screen shows "Running" and the countdown time. Open the WLAN of smartphone, search WIFI network, you can find a network hotspot named for "People Counter", then join the network and make sure the network connection is successful.
 
After the receiver starts AP service (WIFI hotspot), if no smartphone is connected to the “People Counter” network within 30 seconds, the AP service will automatically exit. So you need to notice the countdown time on screen, it will re-countdown each time you touch the screen.
 
If the smartphone has been connected to the “People Counter” network and the browser has accessed the setting page for operation, the AP service (WIFI hotspot) of receiver will keep on. So do not worry about the countdown time.
Note: As the power consumption of receiver will increase largely when starting AP service (WIFI hotspot), it is recommended to quickly complete all the settings and close AP service timely.

If other wireless devices are using or there is WIFI channel interference around the receiver, you may fail to join the “People Counter” network. Try to join several times until network connection is successful.

Open the browser, input this browser address: 192.168.8.1, press Enter (GO), enter the setting page of receiver. The initial password is 1234, you need to enter the password firstly and then choose the setting contents.

3. Standalone Mode Setting

Enter the password in the login interface, click “PARAMETER”, then enter the setting page to set open time, close time, speed and display mode.
Two detection speeds are available: low speed and high speed. If you want to detect pedestrian’s normal speed, please choose “Low”. If you want to detect faster speed, such as running speed, please choose “High”. But note that the power consumption will increase in high speed mode.
There are three display modes for choice. If you do not want other people to see the data on the screen of receiver, please choose "Disable". If you only want to see the sum of the data in two directions, please choose "Total ". If you want to see the in and out data respectively, then choose "Two-way ". Press save, then receiver will update the parameters and calibrate its time according to your smartphone time automatically.
Now the standalone mode settings are done. Exit your mobile browser, after the countdown time on receiver screen is over, the standalone mode will run.

4. Data Browsing

Click “DATA LIST” button in login page, then you can browse the total daily data in the last 30 days and the total monthly data in the last 12 months. You can clear today’s data by clicking “Clear” button.

The data on display screen will be cleared automatically before the open time every day. The total in and out data from open time to close time will be displayed, and the data will not be affected by battery replacement.

1. Q: Are you a factory or trading company?

    A: Our trading company established in 1998 and factory founded in 2006.

    ISO certificated factory.

2. Q: Where is your company and factory located? How can I visit you?

    A: Our company is located in Room 607, Greenland Hechuang Building, No.450, CaoYang Road, Shanghai, China. It takes about 1.5 hours from our company to factory by car. All our clients, from home or abroad, are warmly welcome to visit us!

3. Q: How can I get some samples?

    A: We are honored to offer you samples, most items are free, please feel no hesitation to contact us.

4. Q: How does your company and factory do regarding quality control?

    A: Quality is priority. Highlight always attach great importance to quality controlling from the very beginning to the very end. Our factory comply with the IS09001 standard strictly and most products CE approved.

5. Q: What is your after-sale service?

    A: we offer 100% guarantee on our product and agree 1:1 replace defective products.

6. Q: What is your MOQ?

    A: Any quantity is acceptable for your order. And the price is negotiable for large quantity.

7. Q: When will you make the delivery?

    A: We can make the delivery within 3-15 working days according to the quantity of your order.

        For the popular products, we have in stock and can send it after getting your payment. 

8. Q: How can I contact you now?

A: Contact person: Jasmine Wang    

    Email: team3 at highlight86.com

 Website: www.highlight86.com

               Skype: highlight-team3