![[From EU] 3KW BT30 220V ATC Automatic Tool Changer Water Cooled Spindle Motor+3.7KW Fuling Inverter VFD for CNC Milling Machine](https://img.tradechina.com/image/800.800.80.40.0/bb22cc89d7e73b7099cfef708980fcb9.jpg)
[From EU] 3KW BT30 220V ATC Automatic Tool Changer Water Cooled Spindle Motor+3.7KW Fuling Inverter VFD for CNC Milling Machine
We have Warehouse in Germany,so we can ship from Germany fast delivery and no VAT to EU Countries!!!
1-2 working days to: Germany
2-4 working days to: Austria,France,Spain and Italy
3-5 working days to: UK
|
Free Custom Duty & Free VAT to Below Europe Countries |
||||||
| Austria | Belgium | Bulgaria |
Czech Republic |
Croatia |
Denmark | Estonia |
| Finland | France | Germany | Greece | Hungary | Ireland | Italy |
| Latvia | Lithuania | Luxembourg | Netherlands | Poland | Portugal | Romania |
| Slovakia | Slovenia | Spain | Sweden | UK | Malta | |
Package include:
1 x 3KW ATC Automatic Tool Change Water cooled spindle motor 220V (RTM100-30-24Z/3.0-220V)
1 x 3.7KW 220V VFD Inverter (Fuling Brand) 220V input and 220V output
1 x BT30-ER25 Tool Holder with 45° pull stud
1 x English User manual
Product overview
1.This spindle is built-in type spindle motor, built-in three asynchronous motors,by the inverter control.As the spindle has a compact structure,high power, big torque, small vibration, low noise characteristics,so it can achieve high speed,high powe cutting,high precision and high stability operation.
2.The bearing of spindle use grease lubricated angular to contact bearings,can be achieved lifelong lubricating within the life cycle.
3.The spindle use forced coolling mode to coolling motor,front and rear bearings.Coolant flow through the reasonable arrangement cycle watercourse of the spindle body,thus can take the heat generated of the spindle rotation speed, to achieve thermal equilibrium,let spindle temperature within a certain constant value. External cooling device effect:maintaining a constant temperature of the coolant.
4.The spindle built-in PTC 140 temperature sensor(Technical parameters are visible in other sections of this specification),you can read it anytime if you need to protect the motor temperature. 5. The tool clamping methods:this spindle built-in automatic tool change device,shank form is BT30.
Automatic tool changer electric spindle technical parameters
1.) Product technical parameter table
220V table
|
Spindle model: |
RTM100-30-24Z/3.0 220V |
Voltage: |
220V |
|
Rated speed: |
15000rpm |
Maximum speed: |
24000rpm |
|
Rated frequency: |
250Hz |
Maximum frequency: |
400Hz |
|
Electric current: |
6.7A |
Motor level: |
2 pole |
|
Rated power: |
3.0KW (S1) |
Peak power: |
4.2KW (S6) |
|
Rated torque: |
1.9Nm |
Peak torque: |
2.6Nm |
Technical parameters:
|
No. |
project |
Standard |
|
1 |
Spindle blowing dust/seal gas pressure (MPa) |
0.2-0.25 |
|
2 |
Spindle gas seal gas flow (L/min) |
65±10(When on Working) |
|
3 |
Cooling water pressure (MPa) |
≥0.25 |
|
4 |
Cooling water flow (L/min) |
≥2.5 |
|
5 |
Cooling water temperature (degree) |
24-28 |
|
6 |
Spindle static state pulse (µm) |
≤3 |
|
7 |
Spindle vibration (mm/s) |
≤0.8 |
|
8 |
Spindle diameter (mm) |
Diameter 100 (0/-0.022) |
|
9 |
Motor windings Pressure test (V/M) |
1500V/1 minute withstanding Voltage test |
|
10 |
Tool Interface |
BT30 |
|
11 |
Inverter Specifications |
3.7KW (220V) |
|
12 |
Fitment |
For castings, aluminum, glass, etc., and other processing |
Spindle installation explanation
1.Circulating Cooling System Description
The system must ensure that the cooling water temperature of supply spindle is between 24-28 degree. Usually setting the flow switch in return pipe of the cooling system,to ensure the supply of spindle cooling water. Cooling water requirements: we recommend using distilled water, while recommend Feinuokesi (Fenix) protective agent F1 (using the scale of 1: 200),coolant temperature is 26 degree ±2 degree,inlet, outlet pipe temperature can’t exceed 5 degree.It is allowed As long as other monitoring can ensure fuller spindle cooling.
2.Air sealing control
In order to prevent water or impurities enters internal of the spindle,spindle will have gas sealing device,the gas seal machine must be started start with the machine at the same time. And the need to go through multi-stage filtration.
3.Compressed gas quality requirements
The quality requirement of gas which is used in gas seals: Oil content: <0.01mg/m⊃3; solid particle: <5µ m Pressure dew point: <7.5degree (0.7MPa)
4. Running-in program instructions
Only all monitoring issued no failures operational signals,at the same time,all safety devices have been installed and working properly,then allow start spindle. Note: new or spindle which is not used for a long time must to be running slowly.First,start run spindle for half an hour as 25% of the maximum speed,then increase to 50% of the maximum speed,to run 15 minutes,finally, increase to maximum speed.It’s need to check the temperature of the spindle during the whole process, spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer service department.
Inverter Number: Fuling 220v 3.7kw
Input Frequency: 50-60Hz
Input Phase: 1 or 3 phase
Output Voltage: 220vAC
Output Frequency: 0-1000 Hz
Output Current:15A
Output Phase: 3 phase
Warranty: 2 years from the date you purchased
No PG vector control (SVC): starting torque 0.5Hz up to 150%
8-stage simple PLC function, multi-speed control and PID control
Support multiple frequency settings: digital setting, analog setting, PID setting, RS485 communication setting
I/O terminals can be freely programmed to combine multiple working modes according to user needs.
With jump frequency control function, it can effectively suppress mechanical resonance and make the system more stable and reliable.
With instantaneous power-down retention function, it can avoid the impact of production due to instantaneous power failure
With over torque and under torque detection
Automatic voltage adjustment function to effectively solve the low frequency oscillation problem of high power motor
Provide a variety of fault protection functions: over-current, over-voltage, under-voltage, over-heat, overload, lack of equal real-time monitoring and protection to ensure safe operation
built-in braking unit.
3). BT30-ER25 Tool Holder
1.Q: Where do you ship from?
A: We ship from the Germany warehouse to you,you can place an order directly,and we will ship your order within one working day.
2.Q: What kind of express delivery and when can I receive the goods?
A:We will ship by Germany DHL to you,the package can be tracked from the DHL website.
1-2 working days to: Germany
2-4 working days to: Austria,France,Spain and Italy
3-5 working days to: UK
4-5 working days to: Other Europe Countries
If you need more quantity, please contact us to confirm the specific delivery date, thank you.
3.Q: How is your quality?
A: Each of our products will be tested before packaging to ensure that there are no problems before being shipped.
4.Q: How to return the goods?
A:
> Defect: We will fully refund or send you a new replacement,please contact and return within 30 days.
> Dissatisfaction: Please contact within 7 days,we will fully refund,after got your returned goods.
> Missing parts/Q'ty: Please contact us immediately,for a new package arranged,or a partial refund issued.
5.Q: What are your warranty terms?
A: Most products have a 2-year warranty.We provide different warranty terms for different products.Please contact us for details.
Our company is specialized in CNC system technology research and development, production and marketing of a high-tech enterprises. Mainly products: Desktop CNC Router,Mini Laser/Engraving Machines,Lathe/Milling Machines,ATC Spindle Motor,Air/Water Cooled Spindle Motor VFD Kit,AC/DC Servo Motor/Drivers,Stepper Motor/Drivers,3/4/5/6 Axis CNC Control System etc with well-equipped testing facilities and strong technical force.
We have our own agents and warehouses in the USA,Germany,Czech Republic,UK and Russia etc,so we can ship some products directly from foreign warehouses,which is very convenient.
- Step 1Find your interested products by search keywords
- Step 2Contact the supplier by clicking ”Enquire” or “request meeting” button, otherwise, you also could consult our import consultant.
- Step 3After verifying your email, get response from suppliers or our trade manager will contact you as soon as possible
- Step 4Set up meeting with the Chinese supplier without language barrier