Leak detection required after installation of new pump:

Testing: Use the plug and pluging the pipe to inflate to 20 mpa

when assembled observe the pressure gague after 10s to drop,-do not drop is not leaking, If leaking, then make the pump into water, observe the location of leaking.

Silicone oil and water cooled liquid considerations:

The air pump does not contain silicone oil, For air shipping sercu-rity reasons, oil can be purchased from local store , oil adding should appropriate, if too much it is easy to plug one-way valve water cooled liquid has been added, between 2 and 3 levels stage position, do not need add.

Low pressure on the vent when pressure down:

The operating principle of the pump: pulling up the second-level system, to the tertiary system pressure, the primary system intake. Because the outlet is not connected to the container, the second stage system pressure discharged directly through the third system, so the air vent volume is very small, it is ok.

1. Refueling

New pump, pressing after 8001500eS need refueling once. One place 3 drops of oil, add oil pressing 50 times, drain excess oil and water.

2. Female connector installation

Female connector should be properly installed, otherwise, it is easy to jam

3. Pressure relief

The air pressure must be vented, When not in use, try to keep the pump in the pressure-free state. Hose can't bend over, don't crash pressure gauge.

4.Water Cooling Principle Description

The water of the air-cooled barrel is between the secondary and tertiary tubes. The water has already been added. Sealed inside, no need to add. water-cooled conduction heat, not refrigeration. Fever is normal, indicating that heat is discharged to continue working.

1. One-way clearance

When used upward pull heavy, pressure gauge value rises when downward pressure. The pressure gauge decreases when the hand is loosened. This indicates that the one-way valve has sewage, or has been damaged. Solution: Check whether the valve sludge too much, if a serious rebound phenomenon, is a one-way valve to appear oily, or one-way valve damage. You need to clean up the one-way valve, Replace the valve seal ring or spring

2. Air Intake Clearance

Air pressure when the pump is inflated, press the hand when the vent, pulling out when not breathing. Reason: There are foreign bodies in the small holes in the middle of the hand. The intake ball cannot be returned to the sealing position. Solution: Disassemble the pump, remove the three-stage pole fixation bolt,

remove the air intake ball, clean the small holes and the ball. If the ball is damaged, replace it and install it back.

3. Pressure gauge damage

Pressure gauge does not return to zero: Reason: Excess oil is not cleaned. About20mpa oil and gas produce swelling, pressure instantly reaches 40mpa, pressure gauge exceeds load and then damage. Or the pressure gauge receives a severe shock causing a shift in the pointer, which requires replacing the pressure gauge.

ABOUT US

MINYA is a professional manufacturer of high pressure filling systems for PCP.The best pump choice of refilling hunting air rifle and paintball tank !!

Retail & Wholesale: High pressure 4500 psi pump,Mini 300 bar electric air compressor,Gas cylinder and air tank,Accessories

Feel free to drop us a message to find out how we can work together to grow your business.

A: The product warranty time is one year, if exceed one year warranty time, we will charge a certain part cost expense.

B: The warranty when the repair sent to the proper packing, if the transport process lost damage, we are irresponsible.

C: During free maintenance, if the following matters occur, we have the right to refuse service or charge related material fees, service fee:

1. Improper use of the operation caused product damage or product failure.

2. Arbitrarily disassemble the pump.3. Not the company's products.

D: Before installing the use of our products, please read our brochure carefully.

E : During warranty time, parts free charge, buyers pays hipping charge.

1.How long will it take to fill a 450cc tank?

The first time you fill it will take a longer as you are going from 0-3,000 psi. So the first time like 20-30 min. It will take at least 15 pumps for every 10 bar pressure of your need in the 450cc tank. It all depends on how tough you are really.

2.Can I use this with paintball air tanks or the Pioneer Air bow ?

If you have the right fill adapter for the connector.You can fill them that has a 8mm female Foster quick-disconnect on the end of the pump hose.

3.How long is the microbore hose?

There is a 50cm(20”) hose with the pump.If you need buy a more longer hose, Please send a message to customer service.

4.Can Minya do custom assembly or offer OEM pcp hand pump product?

Minya  is a professional manufacturer of pump and air compressors. Our factory has gained a lot of experience on OEM pcp hand pump assembly of air pump & air compressor.