Wood Pellet Machinery, as named wood pellet machine, wood press machine , is a equipment which is used to press forestry waste, agriclture waste into biomass fuel. It is widely used in biomass pellet plant. |
Model | Main Power(kw) | Capacity(t/h) | Oil Pump (kw) | Steam Fan(kw) | Dimension(L*W*H) | Weight(t) |
YGKJ 450 | 55 | 0.6-0.8 | 2400*1000*1600 | 4 | ||
YGKJ 560A | 90 | 1-0.5 | 0.37 | 1.5 | 2600*1300*2300 | 5.8 |
YGKJ 560B | 90/110 | 1.2-1.5 | 0.37 | 1.5 | 2200*1300*1600 | 5.6 |
YGKJ 700 | 132/160 | 2-3 | 0.37 | 1.5 | 2400*1400*1800 | 7 |
YGKJ 850 | 220 | 2.5-3.5 | 0.55 | 2.2 | 3800*1830*3080 | 12 |
YGKJ 880 | 220 | 3-4 | 0.55 | 2.2 | 3000*1500*2300 | 15 |
Feeding Way | Vertical ring die pellet machine vertical feeding |
Pressing Way | The vertical ring die pellet machine is the mold stationary, the roller roll revolution and rotation |
Installation | Main shaft and motor are respectively installed vertically. Power flat drive. The reserved space of reduction gear box is large, then larger reduction gear box can be installed. Therefore, the reduction gearbox with lower failure rate, stable operation, low power, and large output torque. |
The temperature of Chamber room | The speed of main shaft in vertical ring die pellet machine is 75 rpm, and the press chamber is open. It is easy to dissipate heat and the temperature is up to 150 degrees. Therefore, it can be used with high temperature resistant 200° high temperature butter and also can long life of various wearing parts. |
Cooling Way |
Gear box adopts cooling system,avoid higher oil temperature,service life 5 years gurantee,highly lower the production cost. Main shaft makes use of the gear box gear oil lubrication,lower the main shaft temperature,improve the main shaft span life. |
Lubrication Way | Vertical ring die pellet machine adopts the lubrication way with non-stop and uninterrupted lubrication |
Wood Chipper/Wood ShredderChips wood log, wood branches template budiling waste, agriculture waste into small chips with 3-5cm |
Drum Rotary DryerUsed to dryer sawdust, wood chips, wood shaving, rice husk into suitable moisture. |
High Efficiency Hammer MillCrush wood chips , small size wood brnaches,sugar cane bagasses into 3-5mm sawdust. |
1. What is the whole process for press wood pellets ?
The whole process of press wood pellet depends on the size and moisture of your raw material.For exmaple, if your raw material is wood logs with diameter about 30cm, and the moisture is about 40%.You will need a whole complete wood pellet line.Including Chipping section-Gringding Section-Drying Section-Pelletizing Section-Cooling Section-Screening Section and Packaging Section.
2. What is the most suitable moisture for press pellets?
The most suitbale moisture for wood sawdust or wood shaving is 12-15%.If your raw material is higher than this moisutre, a dryer is need.
3. What is the suitbale size for press wood pellets?
The suitable size of wood sawdust or wood shaving should a little smaller than finished wood pellets.Of course, if the sawdust is too fine, it also not very good.
4. Is Cooling section necessary or not?
Yes, it is necessary. When the pellets leave the pellet machine, it is very hot, soft and releasing moisture. A cooling process is very important stage,Cooling stablities the pellets and hardens the lignin melt on the surface of pellets and hence the shape of pellets remains unchanged.
If you want a detail information about the wood pellet line , you need to offer us these information.
So we can make a more suitable line according to your requirments.
More Information Maybe you also Concerned
If you want to set up a wood pellet line,You should have:
1) Raw Material ,Make sure you can get enough raw material from your place,
In order to reduce cost, the distance of raw materials from your factory is not far than 50km.
2) Factory.
You should have a factory to lay out your factory, to store your raw material and your finished pellets.
3) Transformer.
For pellet line, you should have a bigger transformer .
4)Staff .
For running a pellet line ,you should have enough staff to run this line, for example, wood chipping section need one or two staff.
Dyer section need one staff, pelletizing section need one staff.
The whole line need one staff to control.
For design a suitable line for your,What we need to know
1) What is your raw material? The size and the moisutre?
2) What is your target capacity?
3) What is the size of your factory?
4)How many hours do you want to work per day?
Rotex Master has its own factory.
Here , we offer the most professional design and good quality wood pellet machinery wtih more reasonable price
With us, your money in safe
Your business in safe.
Welcome to contact us
Email:alice(at)rotexmaster.cn
Tel/Whatsapp:0086 15562616769
www.rotexpelletmill.com