Easy Die-cutting 3M UHMW PE Film Tape 5421 for Conveyor thick 0.13MM
Easy Die-cutting 3M UHMW PE Film Tape 5421 for Conveyor thick 0.13MM
Details
Translucent, abrasion resistant backing helps protect surfaces from wear.
Low coefficient of friction for “slip plane” effect between surfaces.
Rubber adhesive provides good initial tack for immediate bonding to material surface.
Can help reduce squeaks, rattles and other noises that occur with movement.
Used in applications where lubrication is not possible because of contaminationUsed in applications where lubrication is not possible because of contamination.
Liner makes it ideal for fabricating or die-cutting into various lengths and shapesLiner makes it ideal for fabricating or die-cutting into various lengths and shapes.
Used to protect surfaces from abrasion, 3M™ UHMW-PE Film Tape 5421 is a thin caliper general purpose polyethylene tape that creates a "slip plane" effect to allow contact without wear. This tape features a unique combination of properties that make it ideal for many tough impact wear or sliding applications. 3M™ UHMW-PE Film Tape 5421 is a thinner version of 3M™ UHMW-PE Film Tape 5423.
Product Description
3M™ UHMW Polyethylene Tapes are film coated with a rubber adhesive which provides an excellent abrasion resistant surface. These tapes feature a unique combination of properties that make it ideal for many tough impact wear or sliding applications. 3M™ UHMW-PE Film Tape 5421 is a thinner version of 3M™ UHMW-PE Film Tape 5423.
Typical Physical Properties
Note: The following technical information and data should be considered representative or typical only, and should not be used for specification purposes.
| 3M tape 5421 | 3M tape 5423 | ASTM Test Method | |
| Adhesion to Steel: | 34 oz./in. width (37 N/100 mm) | 36 oz./in. width (39 N/100 mm) | D-3330 |
| Tensile Strength: | 46 lbs/in. width (796 N/100 mm) | 86 lbs/in. width (1500 N/100 mm) | D-3759 |
| Elongation at Break: | 470% | 530% | D-3759 |
| Backing Thickness: | 5.0 mils (0.13 mm) | 10 mils (0.25 mm) | D-3652 |
| Total Tape Thickness (without liner): | 6.7 mils (0.17 mm) | 12 mils (0.30 mm) | D-3652 |
| Liner Thickness: | 3.5 mils (0.09 mm) | 3.5 mils (0.09 mm) | D-3652 |
| Temperature Use Range: | -30° to 225°F (-34° to 107°C) | -30° to 225°F (-34° to 107°C) | --- |
Features
Tape demonstrated no evidence of wear through after Taber Abrasion at 1000 cycles, using CS-10 wheel and 1000g load when applied to S-37 mounting sheet.
Low water vapor transmission rate <0.50 g/100in.2/24hrs.
Thick caliper UHMW polyethylene tape for extended service life as a protective surface against tough impact wear or sliding applications.
Outstanding abrasion resistance so will outwear PTFE and other materials in sliding applications.
Low coefficient of friction characteristics is exceeded only by PTFE.
UHMW-PE tape can be used where lubrication is not possible because of contamination.
Rubber Adhesive provides good initial tack for immediate bonding to material surface.
Liner makes it ideal for fabricating or die-cutting into various lengths and shapes.
Application Ideas
Noise reduction between dissimilar parts.
Reduce squeaks, rattles and other noises that occur with movement
Lining of conveyer guide rails, tank and bin liners, and discharge chutes.
Protection for aluminum sheets on stretch forming presses.
Liners for Spray booths.
Slick surface for easy glide for drawers and cabinets.
Recommended Applications
Conveyor guide rails and chutes
Spray booth liners
Tank and bin liners
Drawer and cabinet slides
Protecting aluminum sheets on stretch forming presses
- Step 1Find your interested products by search keywords
- Step 2Contact the supplier by clicking ”Enquire” or “request meeting” button, otherwise, you also could consult our import consultant.
- Step 3After verifying your email, get response from suppliers or our trade manager will contact you as soon as possible
- Step 4Set up meeting with the Chinese supplier without language barrier