Digital LED strip UCS1903 WS2811 TM1804 SM16703 LPD6803 remote control Pixel Dream color SPI led controller

Digital LED strip UCS1903 WS2811 TM1804 SM16703 LPD6803 remote control Pixel Dream color SPI led controller 

SPI controller with RF remote control for digital LED strip

HX-SPI01-RFBK controller is suitable for controlling LED lamps driven by a variety of different types of chips. It is widely used in buildings, municipal lighting, stage scenery, entertainment venue decoration, etc.; it can realize horse racing, running water, trailing, color painting, scanning, raindrops Various running change effects; convenient wiring, simple to use; with memory storage function; with digital tube display, which can be controlled by the built-in buttons or with a RF remote control, the remote control has 4 areas of overall control or independent control functions; with multiple online synchronization functions.

Product Feature

1. This product is a low-voltage SPI controller, the standard product supply voltage is 12-24V;

2. Four groups of SPI signal output ports (three-wire digital led strip) or two groups of SPI signal output ports (four-wire digital led strip), which can control up to 2048 pixels;

3. With digital tube and control buttons, it can also be used with RF remote control for mode selection, speed and IC point adjustment;

4. With power-off memory storage function;

5. Contains 136 effect modes, including horse racing, running water, trailing, color brushing, scanning, raindrops and other effects. The 135th mode is the 8-134th automatic cycle mode, and the 136th is the custom combination mode;

6. The controllers can realize multiple synchronous changes through shielded wire connection;

7. The remote control has 4 areas of overall control or independent control functions

8. This product is guaranteed for three years, excluding man-made damage, improper operation, overload short circuit or force majeure factors.

Dimension

Interface Specifications

Direction for use

Instructions for use

l  Determine the controller is the master or the sub-controller, and set the DIP switch at the right position, master-ON, sub-controller- OFF;

l  Connecting the load led strip at first, then connect the power input wires; and make sure that there is no short circuit between the connecting wires before powering on;

l  The functions of the 4 buttons on the controller are as follows:

Parameter setting includes control IC number setting and control IC type setting

In the off state (the controller needs to be powered on), long-press the "UP" and "DOWN" keys at the same time for two seconds, the digital tube displays **** (0010-2048, the current IC point number ) and then enters the parameter setting interface , Press "M/S" to switch between two setting interfaces.

1) control IC number setting

Press "M/S" until the digital tube displays **** (**** is 0010-2048).

Press "UP"/ "DOWN" to increase/reduce the control IC number.

After the setting is completed, press the "ON/OFF" key to save and exit.

2) Control IC type setting

Press "M/S" until the digital tube displays 1903/6803/2801.

Press "UP"/ "DOWN" to switch the control IC type.

1903 for UCS190, TM1804, SM16703 and other compatible ICs.

6803 for LPD6803.

2801 for WS2801.

After the setting is completed, press the "ON/OFF" key to save and exit.

Custom combination mode settings     

This mode is a free combination mode. Choosing 2-20 modes from the 1-134th mode and combine them into a cyclic mode, and each mode can set an independent change speed.

Step 1: In the off state, long-press the "M/S" and "Up" buttons at the same time for 2 seconds to enter Custom combination mode settings, the digital tube will light up and display "-**-", "-**-" represents the currently edited scene number. Please use the "UP" / "DOWN" keys to select the scene number to be edited. For example, we will set a custom combination mode with 5 modes.

Step 2: Setting the mode for -01-. Press "M/S" after Step 1 "-01-", the digital tube will display "H***". Please use the "UP" / "DOWN" keys to select the needed mode from 1-134th for "-01-". If the digital tube displays “H000”, mean there is no effect was set to current scene.

Step 3: Setting the speed for -01-. Press "M/S" after Step 2, the digital tube will display "S-**". Please use the "UP" / "DOWN" keys to select the needed speed from 01-99 for "-01-" mode. The status of loading led strips will be changed accordingly.

Press "M/S" after Step 3, the digital tube will display back to "-01-". Please press "UP" / "DOWN" keys to select the next edited scene number, and repeat the operation like step2 and step 3 to finished the all other 5 scenes from 2^ndto 6^th. And press the "ON/OFF" key to save and exit in the end.

Important notes: When there are less than 20 scenes set, the scene should start from -01- the first number (because the 136th mode runs from scene “01”), and the scenes without effect need to be set to “H000”. Like example that we set 5 scenes to combinate the 136th mode, enter the edit menu and edit the respective modes and speeds of scenes "-01-" to "-05-" (can be not in order during the editing operation). After editing, please check the mode of scene "-06-" should be "H000", if not, please correct it by the "UP"/"DOWN" keys.

Synchronization function

The synchronization control function can be formed by connecting up to 32 controllers, all controllers follow the first master control to achieve synchronous changes without delay.

After all the controllers are connected according to the wiring diagram (please make sure the position of the DIP switch of the master and the sub-controller is correct), just turn on the master, and the sub-controllers will change according to the speed and mode of the master. The green signal light on the sub-controller will flash in normal working statues.

Remote control: RFBK-RGB-2.4G

 Connection diagram

Note: The first one will be the master, please set the DIP switch to ON position; others from the second one will be the sub-control, please keep the DIP switch in the factory default setting -OFF.

About RF code.

The biggest advantage of this system is that it can not only solve the cabling problem in engineering wirelessly, but also realize a wired-like operation experience. In order to facilitate the early testing and debugging of the project, the factory status of the receiver is normally unpaired and each remote controller has a unique code value. The user should perform the matching work of the remote controller and the receiver during the installation of the project to avoid the mutual influence of the radio frequency remote control technology during the later use.

Please pay attention to the following 3 points before operation:

1) All equipment in the complete system after installation should have a unified and unique code value, so as to achieve the security and stability of the system.

2) The receiver can only store one code value and cannot be overwritten. Before learning the new code value, it is necessary to clear the original code of the receiver; the remote controller can only save one code value but can be overwritten and can also restore the factory settings. In order to facilitate the later maintenance, the three components that may be involved in the system (including receivers, handheld remote controllers, and panel remote controllers) can realize mutual learning of code values.

3) Since the receiver performs code value learning in the power-on state, batch-operation is available ( power-one the all receivers which will be in same zone, and operate the matching/clearing the RF code all of them at the same time). And in order to avoid confusion in the area, it is recommended that each area has an independent power switch so that the power of other areas can be easily cut off when the code is being operated.

(1)Code pairing operation: means that the receiver will only be controlled by the value code remote controller.

(2)Code clearing operation: means that the original code value of the receiver will be cleared and returned to the factory state. Then it can be controlled by any compatible remote controller, and can learn to a new code.

(3)Code learning operation between remote controls: Used to unify system code values or copy a new remote controls.

Since each remote controller has its own unique code at the time of delivery, when there are multiple remote controllers in one system, one of them (for example, remote controller A) must be selected as the system code value, and the code value of the rest remote controllers (for example, remote controller B) should be copied to the same one.

(4) The remote controller restores the factory setting: it means that the remote controller will be restored to the factory's unique code value.

About installation of remote control’s bracket:

1.Accessories include: bracket 1pc, 3M foam sponge glue 1pc, screw 2pcs, expansion tube 2pc.

2. There are 2 options for bracket installation:

1) Using screw and expansion tube make drilling installation (suitable for uneven and ash surface);

2) Using 3M foam sponge glue make free drilling installation (suitable for flat no ash surface).

Product information for placing order

Our Services