Didactic Vocational Building Automatic Elevator Training kit DLLY-DT61 Multi layer Elevator Education Training Model
Technical parameter:
1. Input Power: AC380V±10% (three-phase five-wire) 50Hz
2. Rated power: ≤ 1KW
3.Ambient temperature: -10 ℃ ~ 40 ℃
4. Relative Humidity: ≤ 85%
5.Dimensions: 710*500*1800(longth*width*heightmm)
6.P L C: S7-200
7.The frequency converter: MM420
8. Control mode: switch / digital dual control and VVVF technology
9. Floor: Six
Teaching six-story elevator is the most common lift elevator structure made of aluminum sheet, and its structure and the actual lift is exactly the same, and have almost all of the features of the actual elevator. In fact it can be seen as miniaturization elevator. Each action in the elevator is running at a glance, can also be repeated hands-on operation. Enable students to be more intuitive, thorough understanding and grasp of the elevator structure and its operation principle, to achieve a multiplier effect. Therefore particularly suitable for teaching.
Teaching the elevator electrical control system is PLC and AC variable speed (VVVF) control the composition and functions of the hardware structure and the actual elevator exactly the same, with automatic leveling, automatic door switch forward response sedan inside and outside the call ladder signal straight drive, lift the safe operation of the protection functions, as well as the elevator stops, emergency stop, repair, slow, slow down, lighting and fans and other special features.
Mitsubishi FR-D720-0.4KW inverter 220V AC traction motor speed control device. The device on the motor acceleration and deceleration control, positive control, jog control and a variety of functions according to the analog input control. The system logic control completed by the PLC (online). PLC uses the Japanese Mitsubishi FX2N-64MR-type, its output for the relay output form. Is equipped with the RS422 or RS232 interface on the host PLC and PC communication. Using the GX-Developer software directly on a PC with ladder programming, debugging and intuitive to learn, easy for beginners to master; addition can also be used FP programmer II, the directive programming, live debugging
Position detection and electrical layer selection signal of the elevator car installed in the car on top of and connected to the traction sheave of the rotary encoder, in order to get rid rely on relays and contactors, switches, etc. have contact device to control the complexity of the line system, optimized the line, which greatly improves the reliability of the system is running, but also ease of maintenance.
Simulation Teaching elevator hardware and software are used to open architecture. Therefore, the institutions can also use this set of devices for secondary development research. Such as:
An elevator group control (scheduling more than one unified focus alongside the elevator);
Parallel control lift: (2-3 elevator control line parallel logic control, shared landing call button);
(3) the set of selected control of the elevator;
(4) signals to control the elevator.
This set of equipment for learning and teaching, so that the majority of students on the elevator structure, key components and electrical control, the operation of the elevator With the intuitive process, image understanding, easy to deepen the knowledge of the elevator to understand and master. In addition, by using the GX-Developer software directly on a PC with ladder programming and on-site practical debugging for students to understand, learn and master programmable logic controller (PLC) and its applications, as well as industrial process automation control provides a very big help.
Other vocational training equipments
Other FA protucts show:
4.We are in a good position to offer series of training set as follows:
1) Electrical technology Know-how Training Set
2) Innovative E-skills&Technology Training Series
3) MCU Technology Training Series
4) Machine Tools Electrical Control Training Series
5) Machine Tools Electrical Control Training Series(Model-type)
6) CNC Machine Tools Maintainance Training Series(Model-type)
7) Building Automatic Training Series
8) PC Training Series
9) Innovative industrial Automatic Control Technology Training Series
10) Pnematic Training Series
11) Hydraulic Training Series
12) Sensor Training Series
13) Motor Training Series
14) Mechatronic Training Series
15) MPS Training Series
16) FMS Training Series
17) Mechanical Training Series
18) Engrave machine series
5. Packaging And Delivery Details:
Packaging Detail:
1). Packaging for training kit: plastic package + carton + plywood pallets
2). Packaging for training equipment: plastic package + plywood pallet
Delivery Detail: 40 to 50 days after Received advanced payment.
Q1:What factors affect the price?
Q2: All equipments are designed by Dolang?
Q3:Does Dolang have after sales service and training service?
1. After sale service: All our products have one year maintance from the date of pick up except artificial damage.
2. Training: Customer may ask our engineer to training them in their company or come to Dolang for training