1)Center Number | | |
Text command | Parameter | Sample |
CENTER Add | 710#number# 711#number# | 710#13500135000# 711#13800138000# |
CENTER Del | D01# D02# | D01# D02# |
Command Description | 1)Center numbers can control the oil and power and resume factory settings 2) Center numbers can receive the call and text of vibration alarm and over speeding alarm. 3) SIM must display the income call number to control oil and power. 4) Only 2 numbers can be center numbers. | |
2) View Administrator Number | | |
Text command | Parameter | Sample |
View | 901# | 901# |
Command Description | This directive is used to view Device Manager number. | |
Command Feedback | Successful reply:Admin1: Admin2: | |
3)Authorized Number Set | | |
Text command | Parameter | Sample |
Authorized Add | 101# number # 102# number # 103# number # | 1:101#13800138000# 2:102#12345678912# 3:103#12345678912# |
Authorized Del | D11# D12# D13# | D11# D12# D13# |
Command Description | 1) Authorization number for SMS control oil. 2) only three numbers to set the authorization number 3) change the authorization number needs to delete the previous number | |
Command Feedback | Successful Setting:Add Authorization account 1 OK! | |
4) View Authorized Number | | |
Text command | Parameter | Sample |
View authorized | C10# | C10# |
Command Description | This directive is used to view the equipment authorization numbers | |
Command Feedback | Successful Setting: Authorization 1: Authorization 2: Authorization 3: | |
5)APN Setting | | |
Text command | Parameter | Sample |
APN Setting | 802#username#password# | 1:802#intenet#123#123# 2: 802#internet# |
Command Description | APN differs according to the local telecom operators. For example:APN request password,please refer to Sample 1,and Sample 2 for no password. | |
Command Feedback | Successful Setting:SET APN OK! | |
6) Set / View Server | | |
Text command | Parameter | Sample |
SERVER Parameter | 803#SERVER # port# | 803#47.90.39.27#6100# 803#gps.dyegoo.net#6100# |
View SERVER | CIP# | 1)CIP# |
Command Description | Change the IP and port when move to a new server port:10~65535 | |
Command Feedback | Successful Setting:set IP OK! | |
7)Moving Time Interval | | |
Text command | Parameter | Sample |
TIMEER Parameter setting | 730#uploading interval# | 730#20# |
Command Description | Time scope:0,10~60 seconds; 0,no data uploading; | |
| 10~60,means time interval;the default value is 15 seconds. | |
Command Feedback | Successful Setting:SET TIMER OK! | |
8)Static Time Interval | | |
Text command | Parameter | Sample |
STATIC | SUP# time interval# | SUP#5# |
Command Description | Timescope:1~60 minutes;The device has | |
| 3D transmission and the default time interval are 5 minutes. | |
Command Feedback | Successful Setting:SET STATIC TIME OK! | |
9) Cancel the continuous upload | | |
Text command | Parameter | Sample |
NUP | NUP# | NUP# |
Command | This command is used to cancel sending data to the platform | |
Description | If need again to restore the upload , you need to send TIMEER Parameter setting. | |
Command Feedback | SET OK! | |
10)Power-Cut | | |
Text command | Parameter | Sample |
RELAY Parameter1 | 222# | 222# cut off oil and power |
RELAY Parameter2 | 333# | 333# recover oil and power |
| 1)RELAY control the start and closeness of the relay | |
Command Description | 2) Only the center numbers can operate. | |
| 3)the device only cut off the oil circuit on the condition of the driving speed below 20KM/H or in static state. | |
| 4)After send the command, the device will reply ‘please waiting’ When the vehicle speed is over 20KM/H, the device will cut off the oil or the power when the speed below 20KM/H. | |
| | |
Command Feedback | Successful Setting:Fuel cut has already been completed OK! | |
11)GMT | | |
Text command | Parameter | Sample |
GMT | 801#TIME ZONE# | 801#E8# |
| | 801#W5# |
Command Description | The default time zone is Beijing time. If time zone need revised, please operate according to the above command. | |
12)Vibration Sensitivity | | |
Text command | Parameter | Sample |
VIBRATION Parameter | 123#2#alarming way# | 1) 123#2#3# |
Set into | V123#2# | 1) V123#2# |
vibration alarm | | 2) V123#1# |
time | | |
Enable vibration | 911# | 911# |
alarm | | |
Disable vibration | 910# | 910# |
alarm | | |
Command Description | the sensitivity value of the vibration is from 1 to 5,1 is the most sensitive and o is close. Alarming ways: 1, calling 2, texting, 3 calling and texting. | |
| Must set the center number and receiving number. | |
Command Feedback | set vibration alarm level,OK! | |
13)Speeding | | |
Text command | Parameter | Sample |
SPEEDING Parameter | SSA#120#alarming way# | 1)SSA#120#3# |
| | 2)SSA#120# |
Cancel Speed alarm | CSA# | CSA# |
Set speed alarm time interval | STIME#MINUTES# | STIME#5# |
| SCOPE:1—60minutes | |
Command Description | The speed scope is form 60-220, if the speed is no this cope, the alarm is off. | |
| Alarming :1, calling 2, texting, 3 calling and texting. | |
| Must set the center number and receiving number. | |
14)Reset | | |
Text command | Parameter | Sample |
RESET | 930# | 930# |
Command Description | Reset the device | |
Command Feedback | Successful Setting:Reset system, ok! | |
15)Factory | | |
Text command | Parameter | Sample |
Parameter | 940# | 940# |
Command Description | Restore the factory setting | |
| Only center number can initial this function | |
| Factory setting will recover to the original setting | |
Command Feedback | Successful Setting:FACTORY OK! | |
16)Language Setting | | |
Text command | Parameter | Sample |
LANG Parameter | LANG1# | LANG1# 1:CHINESE, |
| LANG0# | LANG0#:ENGLISH |
Command Description | ;When check the location, it will reply the Chinese location in Chinese language setting; while reply the URL link when in English language setting. | |
Command Feedback | Successful Setting:SET LANG OK! | |
17)Position | | |
Text command | Parameter | Sample |
WHERE | 666# | 666# |
Command Description | Check the longitude and altitude and other | |
| information of the device | |
Command Feedback | Reply with longitude and altitude, speed and IMEI. | |
18)Version | | |
Text command | Parameter | Sample |
VERSION | V00# | V00# |
Command Description | The command is to check the software version | |
Command Feedback | VERSION:Xxxx | |
| BUILD:2012-07-05 10:12 | |
19)Param Check | | |
Text command | Parameter | Sample |
PARAM | 886# | 886# |
Command Description | The command is to check the settings and the default parameter. | |
Command Feedback | IMEI:351190012535936 | |
| APN : cmnet | |
| IP:IP and port | |
| TIMER: moving uploading interval | |
| STATIC: static uploading interval | |
| CENTER: center number | |
| LANG: language(CN/EN) | |
| GMT: time zone (E/W8) | |
20)Status Check | | |
Text command | Parameter | Sample |
STATUS | 902# | 902# |
Command Description | The command is designed for checking the device’s working status. | |
Command Feedback | External power:ON/OFF | |
| GSM Signal:HIGH/MIDDLE/LOW | |
| GPS:FIXED/UNFIXED | |
| RELAYER:DISABLE/ENABLE | |
| Vibrate Warning:ON/OFF | |
| Pause:ON/OFF | |