Concrete Formwork Spring Coil Ties Concrete Plywood forms snap tie
Concrete Formwork Spring Coil Ties Concrete Plywood forms snap tie Plywood forms snap tie
The Coil Ties System consists of 4 components :
Coil Tie
Coil Ties have 2 opposing wire struts which are welded to a steel
coils at each end of the coil tie.
- Coil Tie Bolt
The Coil Tie Bolt is a coarse threaded bolt with a hexagonal head and fixed washer.
- Coil Tie Cone
Plastic Coil Tie Cones are screwed to each end of the coil tie so that the coil tie is recessed back from the face of the concrete.
- Plate Washer
The steel Plate Washer is fixed against the timber walers and held in place by the Coil Tie Bolt.
This system is used to accurately space the opposing formwork shutters apart to achieve the dimensional thickness of a concrete wall. Once the concrete for the wall has been poured and the formwork removed, the Coil Tie Cones are removed. The Coil Tie remains in the concrete.
Other Coil Tie System Accessories :
- Coil Tie Threaded Rod
This has the same thread as the Coil Tie Bolt. It is supplied in 3.0m lengths and can be cut to size.
- Coil Tie Wing Nut
The Coil Tie Wing Nut is a double wing cast steel nut used with the Coil Tie Threaded Rod.
- Coil Tie Cone Remover
Designed for the removal of Coil Tie Cones.
- Concrete Plugs
Concrete Plugs are used to plug up the hole left by the Coil Tie Cone and produce a recess finish to the concrete.
| Coil Tie: | 150mm to 600mm in increments of 25mm |
| Coil Tie Bolt: | 250mm, 300mm, 350mm, 400mm, 500mm & 550mm |
| Coil Tie Cone: | 12.5mm, 25mm, 37.5mm, 50mm |
| Plate Washer: | 125 x 100 x 8 |
Z BAR SYSTEM
The Z Bar System is a high load tie system which consists of 5 basic components :
| Z Bar: | Z Bar is a hot rolled, high tensile steel bar available with a nominal dia. of 15/17mm. It is used in high load situations for wall formwork ties and features a high speed thread allowing wing nuts to be fitted and removed quickly. Z Bar is also available in a cold rolled steel bar with a nominal dia. of 15/17mm and has a lower tensile rating than hot rolled Z Bar. |
|
| Single Arm Wing Nut: | The Single Arm Wing Nut is a cast steel nut designed for quick installation and removal. The single arm helps to prevent the nut from unwinding caused by vibration of the concrete. | |
| Plastic Conduit Cone: | The cones are fixed to each end of the plastic conduit to recess the conduit back from the face of the concrete. They are removed after the concrete is poured. | |
| Plastic Conduit: | The Plastic Conduit is used for the easy removal of the Z Bar. The Plastic Conduit is supplied in 3.0m lengths and cut to size to suit the concrete wall thickness. | |
| Plate Washer: | Steel Plate Washer 125mm x 125mm x 10mm is fixed against the timber walers and held in place by the Single Arm Wing Nut. |
OTHER Z BAR ACCESSORIES
| Swivel Wing Nut: | Combination washer and nut. The nut swivels on the washer providing extra adjustment. | |
| Cast Nut Washer 100mm: | Fixed nut with 100mm circular washer. | |
| Cast Nut Washer 130mm: | Fixed nut with 130mm washer. | |
| Hex Nut 50mm: | Can be used in place of Single Arm Wing Nut. | |
| Hex Nut Coupler 100mm: | The Hex Nut Coupler is designed to join 2 lengths of Z Bar. Each bar needs to be screwed up to the middle of the coupler. | |
| Double Arm Wing Nut 20/22: | The Double Arm Wing Nut is used with 20/22mm Z Bar. | |
| Water Barrier: | The Water Barrier is used as a water stop to prevent leakage through the tie hole. It is left in place after the concrete is poured. | |
| Steel Cone Nut: | The Steel Cone Nut screws directly onto the Z Bar and is removed after the concrete is poured. The Z Bar is not recoverable. It is available in 75mm and 100mm long |
ACCESSORIES & HARDWARE
Soffit Spacers
They are available in sizes ranging from 150mm up to 600mm in increments of 25mm
NAILS
Bullet Head Nails
Sizes and range are as follows :
| Item | Description | Type | Qty per Tub/Pack |
| 2” Nail | 50mm x 2.8mm | Bullet Head Bright Finish | 15 kg |
| 3” Nail | 75mm x 3.6mm | Bullet Head Bright Finish | 15 kg |
| Fillet Nail | 30mm x 2.0mm | Bullet Head Bright Finish | 5 kg |
| Item | Description | Type | Qty per Tub/Pack | Fuel Cells |
| 2” Nail | 50mm x 2.87mm | D-Head Collated | 3000 | 3 |
| 3” Nail | 75mm x 3.06mm | D-Head Collated | 3000 | 3 |
| 2” Nail | 50mm x 2.87mm | D-Head Collated | 3000 | – |
| 3” Nail | 75mm x 3.06mm | D-Head Collated | 3000 | – |
| Bolt Dlameter | SWL Tension | Height (c) | Coil Length (B) | Wire Diameter(D) | Length(A) | Min Edge Distance |
| In | Ib | In | In | In | In | In |
| 3/4 | 4500 | 1-5/8 | 1-3/4 | .375 | 6 | 8 |
| 1 | 6000 | 2-1/4 | 2-1/16 | .440 | 6 | 8 |
| 1-1/4 | 7500 | 2-1/2 | 2-1/16 | .440 | 8 | 10 |
| Bolt Dlameter | SWL Tension | Height (c) | Coil Length (B) | Wire Diameter(D) | Length(A) | Min Edge Distance |
| In | Ib | In | In | In | In | In |
| 3/4 | 4500 | 1-5/8 | 1-3/4 | .375 | 6 | 8 |
| 1 | 6000 | 2-1/4 | 2-1/16 | .440 | 6 | 8 |
| 1-1/4 | 7500 | 2-1/2 | 2-1/16 | .440 | 8 | 10 |
Qingdao Gold Power Machinery Co.Ltd is a professional factory to make rigging hardware, electric power fittings, concrete forming hardware and other OEM etc, the factory covers an area of 10,000 square meters and its architectural area is 5,000 square meters, it has over 150 staff, including 5 engineers, 15 specialized Technician, two forging workshops, one mold workshop, main equipment is /630T/400T/300T/160T forging machine, air hammer, heating furnace, rolling machine, tapping machine, blasting machine and also we have welding machine and CNC machining workshop to do more process Main products comprise Building Concrete Products(coil rod ,coil insert ,coil tie ,coil cone ,jack ,nut ,plate,scaffolding accessory,foot anchor ,lifting anchor ) Poleline accessories, Powerline fittings( like anchor rod,ground screw anchor ,no wrench anchor rod,screw anchor ,helix anchor rod ,helix pile ), anti hail accessory (wire tensioner,anchoring clamp,wire tender,wire collar wire rope ,wire strand , anti hail net,wire anchor clamp ,wire stretcher),Rigging hardware(shackle, turnbuckle ,and wire rope clip) other OEM items.
PRODUCTION :
We Supply OEM Design
Fast Price Offer
Quick Delivery
QA report and Material Report offered
Production Process QA offered
We tackle the Troubles and Problems For you
Contact
AMANDA XUE
Whatsapp: 86 13188978757
WeChat: 86 13188978757
- Step 1Find your interested products by search keywords
- Step 2Contact the supplier by clicking ”Enquire” or “request meeting” button, otherwise, you also could consult our import consultant.
- Step 3After verifying your email, get response from suppliers or our trade manager will contact you as soon as possible
- Step 4Set up meeting with the Chinese supplier without language barrier