Video technical support, Online support, Spare parts, Field maintenance and repair service
Local Service Location:
Viet Nam, Indonesia, Pakistan, Thailand, Malaysia, Bangladesh
After-sales Service Provided:
Engineers available to service machinery overseas
Certification:
ASME, ISO9001,CE GOST DOSH
Supply Ability
Supply Ability:
500 Unit/Units per Month CFB Power Plant Boiler
Packaging & Delivery
Product Description
The CFBC boiler is mainly composed of four parts: furnace area, tail shaft area, cyclone separator and "U" type fuel return device. The furnace is composed of membrane walls. The bottom of the furnace is a water-cooled air chamber surrounded by membrane wall tubes, which are connected to the primary air duct through expansion joints.
A high temperature cyclone separator is arranged between the furnace and the tail shaft, and a "U" type fuel return device is arranged at the lower part.
The tail shaft is arranged in order from top to bottom with five stages economizer and two stages air preheater. The front wall of the fluidized bed is equipped with two coal seeding devices. The interface between the furnace bottom air chamber and the primary air duct can be easily installed with an oil or natural gas ignition device.
The boiler is symmetrically arranged on the left and right, and is supported on the steel frame of the boiler.
Membrane wall
Ø the furnace adopts full membrane wall Ø water cooled wind chamber Ø tube size Φ60X5 Ø tube material
20(GB3087) - medium pressure 20G(GB5310) - high pressure Ø pitch:80mm / 105mm Ø flow gas speed:4.8m/s
Ø longitudinal pitch 90mm Ø material 20(GB3087) 20G(GB5310) Ø The flue gas speed less than 8 m/s Ø The medium speed less than 1 m/s
Air preheater
Ø Vertical、horizontal arrangement; Ø Primary and secondary parallel arrangement; Ø Tube size:Φ51X1.5 mm(Vertical) Φ40X1.5 mm(Horizontal) Ø Material:Upper part Q235B, tail end low temperature use the coten steel or enamel pipe
Steel structure
ØThree parts: 1. Roof system, 2. Beam, column and support system 3. Platform and ladder system ØThe platform width is 0.85m or 1m. Ø The ladder width is 0.7m,inclination angle 45° Ø The handrail and baluster adopts Øgalvanized tube, size is Φ1 ØThe baluster pitch is 1~1.2m Ø The handrail height 1.2m
Nozzle
Ø water cooling type wind distribution plate Ø New immersion bell nozzle ØAdvantage:Rational structure, even air distribution, steady fluidization, no leakage, anti-coking and slag sediment
Cyclone separator
ØCyclone Separator :Consist of Straight, Cone, Dipleg and Central cylinder Ø Type:Adiabatic type、Water-cooled type , Steam-cooled type Ø Central cylinder material:16Cr25Ni20Si2
Fuel recycle device
Ø Use the non-mechanical U-type recycle device value * Self-balancing returning ash without running control * Air supply and system simply, * It is better for uniform distribution of circulating ash in furnace
Ø The material-returning wind is provided by roots blower * small flow * High pressure head
CFBC boiler characteristics--energy saving
Reduce physical incomplete combustion loss
1. Reduce the slag carbon content to 1%
2. Bell type nozzle labyrinth layout, no ash leakage, no dead point of wind distribution, more uniform 3. New secondary air arrangement, stronger secondary air penetration and better combustion effect 4. The particle size of the fuel is controlled within 10mm 5. Reduce the carbon content of fly ash to 5% 6. The clear height of the hearth is 1.5 ~ 2 meters higher than similar products. 7. Moderate fluidization speed (4.5 ~ 5.5m / s). The residence time is greater than 5s. 8. Choose the best cycle rate to improve separation Device separation efficiency, to ensure that the fuel is burned multiple times.
1.1 The heating surface of the furnace is reasonably designed. The combustion temperature is about 865℃. Its the optimal temperature range for desulfurization and denitration. The area of the furnace, cyclone separator, superheat screen, superheater, and economizer is revised accordingly.
1.2 According to the type of coal, measures such as adding limestone powder to the furnace refeeder and desulfurization tower after the furnace are adopted to ensure that the original emissions of SO2 are below 100mg/Nm3
2. Integrated denitrification design
2.1 Design bed temperature is about 865℃
2.2 Low oxygen content design, oxygen content is controlled at 3%
2.3 Strictly graded air supply, primary air control below 50%
2.4 Ensure that the NOx emission at the furnace outlet is below 200mg/Nm3, and the minimum NOx can be below 30mg/ Nm3
2.5 The furnace outlet is equipped with SNCR equipment, which can control NOx emissions to a lower level.
Packing&Shipping
Because of its large size, CFBC boilers are shipped in bulk and assembled at the construction site.Pressure components will be hydrostatically tested in the workshop and tested again after installation on site.
After Sales Service
1. Engineers availiable to after-sale service oversea.
2. Onling support
3. Video technical support
4. Supply spare parts
Company Introduction
Taishan Group Co., Ltd. Is located at the foot of world-famous Mount Tai, neighbors with Jinan city and Confucius's hometown-Qufu. The east is Beijing-Shanghai high-speed railway, the west is Beijing-Fuzhou,Beijing-Shanghai expressway. The distance between Taishan Group and Jinan international airport is 70 kilometers and 480 kilometers to Qingdao international port, the transportation is very convenient. Taishan Group covers an area of 1020, 000 square meters, has more than 4100 employees. lts total assets are 3. 6 billion RMB. Taishan Group has 12 subsidiary manufacturing companies, 2 boiler product development centers, 2 pressure vessel product development centers and 1 import and export trade company. Currently, the annual boiler manufacturing ability of Taishan Group is 650 sets/8500t.
Semi-Automatic PET Bottle Blowing Machine Bottle Making Machine Bottle Moulding Machine
PET Bottle Making Machine is suitable for producing PET plastic containers and bottles in all shapes.
Contact information
No desirable products?
Sourcing assistant>
How to start your business
Step 1
Find your interested products by search keywords
Step 2
Contact the supplier by clicking ”Enquire” or “request meeting” button, otherwise, you also could consult our import consultant.
Step 3
After verifying your email, get response from suppliers or our trade manager will contact you as soon as possible
Step 4
Set up meeting with the Chinese supplier without language barrier