Ceiling Mount Indoor Small 220V/AC ST06A PIR Human Body Motion Detector Switch Sensor
The product adopts good sensitivity detector and integrated circuit. It gathers automatism, convenience, safety, saving-energy and practical functions. It utilizes the infrared energy from human as control-signal source and it can start the load at once when one enters detection field. It can identify day and night automatically. It is easy to install and used widely.
SPECIFICATION:
Power Sourcing: 110 -130V/AC 220 -240V/AC Detection Range: 360°
Power Frequency: 50/60Hz Detection Distance: 3-6m (<24℃) adjustable
Ambient Light: <3-2000LUX (adjustable) Working Temperature: -20~+40℃
Time Delay: Min.10sec±3sec Working Humidity: <93%RH
Max.7min±2min Power Consumption: approx 0.5W
Installation Height: 2.2-4m Detection Moving Speed: 0.6-1.5m/s
Rated Load: 110 -130V/AC : 220 -240V/AC :
800W(incandescent lamp) 1200W(incandescent lamp)
200W(energy-saving lamp) 300W(energy-saving lamp)
Lifetime and Warranty:
Lifetime (hr) |
26000-45000 at least |
Warranty |
3 years |
FUNCTION:
Ø Can identify day and night: The consumer can adjust working state in different ambient light. It can work in the daytime and at night when it is adjusted on the “sun” position (max). It can work in the ambient light less than 3LUX when it is adjusted on the “moon” position (min). As for the adjustment pattern, please refer to the testing pattern.
Ø SENS adjustable: It can be adjusted according to using location. The detection distance of low sensitivity could be only 3m and high sensitivity could be 6m which fits for large room.
Ø Time-Delay is added continually: When it receives the second induction signals within the first induction, it will restart to time from the moment.
INSTALLATION ADVICE:
As the detector responds to changes in temperature, avoid the following situations:
Ø Avoid pointing the detector towards objects with highly reflective surfaces, such as mirrors etc.
Ø Avoid mounting the detector near heat sources, such as heating vents, air conditioning units, light etc.
Ø Avoid pointing the detector towards objects that may move in the wind, such as curtains, tall plants etc.
CONNECTION:
Ø Please move the upper cover with anti-clockwise whirl as per the diagram in the crust.
Ø Connect the power and the load to sensor as per the connection-wire diagram.
Ø Fix the bottom on the selected position with the inflated screw.
Ø Install back the upper cover on the sensor and whirling clockwise the cover until the green light is bared, then you could switch on the power and test it.
CONNECTION-WIER SKETCH DIAGRAM:(See the below figure)
SENSOR INFORMATION:
TEST:
Ø Turn the LUX knob clockwise on the maximum (sun). Turn the TIME knob anti-clockwise on the minimum (-). Turn the SENS knob clockwise on the maximum (+).
Ø Switch on the power; the sensor and its connected lamp will have no signal at the beginning. After Warm-up 30sec, the sensor can start work .If the sensor receives the induction signal, the lamp will turn on. While there is no another induction signal any more, the load should stop working within 10sec±3sec and the lamp would turn off.
Ø Turn LUX knob anti-clockwise on the minimum (moon). If the ambient light is more than 3LUX, the sensor would not work and the lamp stop working too. If the ambient light is less than 3LUX (darkness), the sensor would work. Under no induction signal condition, the sensor should stop working within 10sec±3sec.
Our company adopts automatic machines, such as: SMD, auto component inserter, wave solder, autoinjection machines,the daily output is up to 20000-30000 pcs.
The concept of our company is"advocating new modern living environment",which focuses on researching and developing the contemporary household intelligent product.Our product can be truly satisfied for different customer's requirement,most of them are available with CE GS ROHS R&TTE REACH certification.