CS150 Electrochemical Workstation

CS150 Electrochemical workstation /Potentiostat / Galvanostat contains a fast digital function generator, high-speed data acquisition circuitry, a potentiostat and a galvanostat. With high performance in stability and accuracy with advanced hardware and well-functioned software, it is a comprehensive research platform for corrosion, batteries, electrochemical analysis, sensor, life science and environmental chemistry etc.

Support 2-, 3- or 4-electrode system
Potential control range: ±10V
Current control range: ±2A
Potential control accuracy: 0.1%×full range±1mV
Current control accuracy: 0.1%×full range
Potential resolution: 10μV(>100Hz), 3μV (<10Hz)
Current sensitivity: 1pA
Potentiostat rise time: <1μs (<10mA), <10μs(<2A)
Reference electrode input impedance: 1012Ω||20pF
Current range: 2nA~2A, 10 ranges
Compliance voltage: ±21V
Maximum current output: 2.0A
CV and LSV scan rate: 0.001mV~10,000V/s
CA and CC pulse width: 0.0001~65,000s
Current increment during scan: 1mA@1A/ms
Potential increment during scan: 0.076mV@1V/ms
SWV frequency: 0.001~100 kHz
DPV and NPV pulse width: 0.0001~1000s
AD data acquisition: 16bit@1 MHz,20bit@1 kHz
DA Resolution: 16bit, setup time: 1μs
Minimum potential increment in CV: 0.075mV
IMP frequency: 10μHz~1MHz
Low-pass filters: covering 8-decade
Potential and current range: automatic
Communications Interface: isolated Universal Serial Bus (USB 2.0)
Operating System: Windows 2000/XP/ Win7/Win8/Win10
EIS
Signal generator:
Frequency range: 10μHz~1MHz
Frequency accuracy: 0.005%
AC signal amplitude: 1mV~2500mV
Signal resolution: 0.1 mV RMS
DC Bias: -10~+10V
Output impedance: 50Ω
Waveform: Sine wave, triangular wave and square wave
Wave distortion: <1%
Scan mode: Logarithmic/linear, increase/decrease
Signal analyzer:
Integral time: minimum: 10ms or the longest time of a cycle
Maximum: 106 cycles or 105s
Measurement delay: 0~105s
DC offset:
Potential automatic compensation range: -10V~+10V
Current compensation range: -1A~+1A
Bandwidth: 8-decade frequency range, automatic and manual setting
System Requirements
Operating System: Windows XP / Vista /7/ 8/10.
Communication between PC and instrument: USB2.0.
Dimensions(cm):36 ×30×14; weight: 6.5kg

Stable polarization:

Open Circuit Potential (OCP), Potentiostatic (I-T Curve), Galvanostatic, Potentiodynamic (Tafel plot), Galvanodynamic
Transient polarization:

Multi-Potential Steps, Multi-Current Steps, Potential Stair-Step (VSTEP), Galvanic Stair-Step (ISTEP)
Voltammetry:

Cyclic Voltammetry (CV), Linear Sweep Voltammetry (LSV)
Corrosion testing:

Cyclic polarization curve (CPP), Linear polarization curve (LPR), Electrochemical Noise (EN), Zero Resistance Ammeter (ZRA), Electrochemical Potentiokinetic Reactivation(EPR)
Battery testing:

Battery charge and discharge, Galvanostatic charge and discharge
Extensions: Data Logger, Disc machine control, Bulk electrolysis with Coulometry

Instrument host CS150 x 1

CS Studio software x 1
Dummy cell x 1
Power cable x 1
USB cable x 1
Electrode cable x 2

Manual x 1

Below picture is the supply list for one of our customers.