CE certificate Nonpressure gasoline welding and cutting machine

Ideal, environmental-friendly and innovative way to welding and cutting

2.5 gallons of gasoline = 250 cubic feet of acetylene! 

Economize on energy more than 80%

We can make your welding and cutting works

faster

safer

low cost

less pollution

more efficiency

Advantages:

1)Economical: 

Savings in the Fuel

 In the TWA system, 2.5 gallons of gasoline will cut as much steel as 250 cubic feet of acetylene!  A steady cutting job can easily use 200 cubic feet of acetylene per day, while the same job could be done with 2 gallons of regular gasoline, plus your usual oxygen. That's about $8.00 worth of cutting fuel compared to $90 to $130 for acetylene. 

Savings by Increased Productivity 

Gasoline far outperforms acetylene.  High performance means more work done in less time. 

Savings in Oxygen Consumption 

With TWA there is no increase in oxygen use, and the work gets done much faster.

2)High cutting quality and cutting speed

The cutting sides are smooth and neat without overburned remains. The temperature of the cutting flame is as high as 3000~3300 degrees, so it takes very short time for preheating.To cut a 20mm thick steel plate under 20℃, the cutting speed is about 500mm/m.

3)Safe and reliable

Since the fuel is in liquid state, there is no backflash risk exist. Inside the gasoline tank, there is explosionproof material so  there is no explosion. It is very safe for the operators.

4)Easy to operate and carry about due to the light weight.

5)Environmental friendly

When it works, it doesn't produce much hazardous gas as oxy-acetylene cutting torch does.

6)Wide usage

The max.cutting thickness of this product is up to 400mm,it can be used in many industries which are related to steel cutting such as shipbuilding, automobile, construction, demolition, mining, machining, repair, metal recycling etc.

Features are:

1, electricity.

2. There is pressure in the tank and oil belt.

3. The pressure type is a manual use of a gas cylinder to press the tank.

4, adjust the neutral burning oil, oxygen and tone.

The pressureless gasoline cutting torch has two kinds of casings and tanks, and the operation method is the same.

Features are:

1, no electricity, no pressure, a valve to adjust neutral combustion.

2. The working principle is a qualitative change, the operation is simpler and the use is safer.

The consumption reduction is more obvious.

Advantages of pressureless gasoline welding machine

I. Safe and Reliable

The safety performance of this product is better than that of acetylene and other gas. It does not temper or ignite. The tank is filled with military explosion-proof and anti-combustible materials, which can control the explosion probability to zero. There is no possibility of explosion when the oil tank is exposed to high temperature open flame and the oil tank is repaired with oil.

Second, the cutting quality is good, easy to use and flexible

Use this product to cut the workpiece, the cutting seam is flat, the slit is narrow, no knot, no upper edge of the incision, less slagging on the lower edge, simple cleaning. The product is small in size, light in weight and easy to carry. The whole set of products weighs about 7kg, and the fuel can be purchased anywhere at any time.

Third, the economy is good, the cost is low.

The oil consumption of steel plates under 40mm is 0.4-0.6 liters per hour. The cutting time of 2.5 liters of gasoline is the same as the cutting time of one can of acetylene in the current standard. The workload is equivalent and the energy saving effect is more than 85%. One hour of work per torch can save RMB 20 yuan.

Fourth, the cutting speed Gasoline and acetylene cutting flame temperature is equivalent, up to 2950 ° C - 3600 ° C (adjustable). When the temperature is 20 °C, the product is cut with 20mm steel plate, the preheating time is 3S-4S, and the cutting speed can reach 550mm/min.

Fifth. Wide application, cut and weldable.

Where the oxygen-acetylene flame can be welded and cut, the product can be processed by cutting, welding and so on. At the same time, this product can also fire glass, stone baking surface, preheating and correcting workpieces.

Sixth, green, no pollution, no noise, no electricity, no heating, no residual oil, low cost, no harm to the operator, and the operation method is exactly the same as acetylene cutting and welding torch, the operator adapts quickly, is The best way to solve the acetylene pollution.