Infrared catalytic gas heater
1. Specifications
Now based on catalytic technology, we manufacture one model gas heater for poultry house, with two ways to ignition: manual ignition (THD2606) and auto-ignition type (THD2608).
MODEL | N. W. | Dimension | Consumption | Heat Output | |||||||
kg | mm | NG(m3/h) | LPG(kg/h) | Biogas | Kw/h | Kcal/hr | |||||
| Manual Ignition Heater | ||||||||||
THD2606 | 1.7 | Out cover 320*270*130, Ceramic plate188*135 | 0.24 | 0.18 |
0.5 | 2.46 | 2116 | ||||
| Automatical Electric Ignition Type Heater | ||||||||||
THD2608 | 2.7 | Out cover 320*270*130, Ceramic plate188*135 | 0.24 | 0.18 |
| 2.46 | 2116 | ||||
Electric Pulse Igniter |
| 220VAC/50Hz or 110VAC/60Hz | |||||||||
Ignition Pin |
| 3-pin type | |||||||||
Solenoid Valve |
| Gas diameter 1/4'' inch. 220VAC/50Hz or 110VAC/60Hz |
Detail photo:(THD2606) Manual Ignition Heater
Detail photo: (THD2606) Manual Ignition Heater with adjust valve
2) Material
Shell: heat-resisting aluminized steel
Inner plate: cordierite honeycomb plate with rare-earth catalyst-coated (black)
Safe switch: copper flame-out protection device, automatic ignition system
3) Advantages:
1. Easy being fixed
2. Energy savings can be as high as 50% per year
3. Environmental protection: CO≤80ppm;NOx≤10ppm;CHx≤50ppm
4. No need for a long and expensive preheating, it will reach comfort temperature very quickly.
5. Long useful time: ≥11000hr
6. Easy to clean
7. It can cut off the gas automatic and protect the burner when the flameout.
8. Silent, light and compact
9. High efficiency: it can come to working condition in 8seconds.
4) Application
1. Poultry-livestock heating: widely used in poultry heating, farrowing, nursery, grower-finisher, wean-to-finish
2. Commercial Heating of sports hall, church, terrace, garage, exhibition hall, public building
3. Industrial Heating: industrial building, workshop, vehicle repair, warehouse.
Experience data for poultry farm:
A heater can heat for more than 600chicks;Height from ground is usually 0.9m~1.5m
2. Working system for Manual and Electric Ignited Type
2-1-1) Safe valve device for Manual ignition type
For the manual ignition type, we match with an air safe valve. It is made of copper. First press the switch and let gas in, then ignite by match or lighter. As the gas is firing ,air volume in the copper pipe go up and make the push out the switch, keep the gas going in. Once the gas is not fired or burning abnormally, the switch will keep off so that protect the gas heater security
Working: controlling the heat output through regulate the high and low pressure, need manual ignition
2-1-2) Manual ignition thermostat system:
.
2-2-1) Working system for Electric auto-ignition thermostat system: auto-controlling, ignition system. Only need set a temperature on the controller, the gas heater is ignited or turn off by controller to keep stable temperature.
2-2-2) Electric auto-ignition thermostat system diagram
2-2-3) Working purpose
Open the gas valve, adjust the combustible gas pressure to 3500~5000pa by pressure regulating valve. Open the main power switch on controller and set the needed temperature on controller, then open the burner ignition switch, the solenoid vale supply gas for gas heater when the pulse igniter is electrified. At the same time, the pulse igniter outputs high voltage to ignition pin, and ignition needle produces electric arc so as to ignite the combustible gas in heater. Heater start work
When the thermocouple reacts the room temperature reach the setting temperature, controller will shut of solenoid valve. Gas heater stops work. Later, when sensor react the temperature is lower than setting temperature, the solenoid valve will restart to supply gas after the pulse igniter gets signal from temperature controller. Meanwhile, the pulse igniter outputs high voltage to ignition needle and re-ignite the heater, it works again. By this circulate system, it can keep a very stable and total automatic heating system.
2-2-4) Flameout Protection
When the electric arc produced by ignition needle doesn’t ignite the flammable gas in infrared catalytic burner, pulse igniter will stop outputting high voltage and shutting solenoid valve to supply gas. It will prevent the gas from leakage and sure security.
If need to start again, you must open the ignition switch and pulse ignition of electric cabinet to get electricity, to reboot your ignition system normal working.