model | ESPA1 | ESPA2 | ESPA2 MAX | ESPAB MAX | ESPA4 | ESPA4 MAX | |||||||||
t y p e | size | 8 inches | |||||||||||||
Membranematerials | Aromatic polyamide composite | ||||||||||||||
Effective film area | Ft2 | 400 | 400 | 440 | 440 | 400 | 440 | ||||||||
M³ | 37.2 | 37.2 | 40.9 | 40.9 | 37.2 | 40.9 | |||||||||
performance | Desalination rate | average | 99.4 | 99.6 | 99.6 | 99.3 | 99.2 | 99.2 | |||||||
minimum | 99.2 | 99.5 | 99.5 | 99.0 | 99.0 | 99.0 | |||||||||
Water production | gpd | - | 93.0 | 93.0 | 96.0 | - | - | ||||||||
m3/d | 12000 | 9000 | 12000 | 9000 | 12000 | 13200 | |||||||||
The test conditions | NACL solution concentration mg/L | 45.4 | 34.1 | 45.4 | 34.1 | 45.4 | 50 | ||||||||
Pressure,psi(MPa) | 1500 | 500 | |||||||||||||
Temperature,℃ | 150 (1.05) | 100 (0.7) | |||||||||||||
Recovery rate of single film element,% | 25 | ||||||||||||||
test liquid PH | 15 | ||||||||||||||
Conditions of use | Maximum inlet pressure, psi(MPa) | 6.5-7.0 | |||||||||||||
Maximum inflow rate,gpm(m³/h) | 600 (4.14) | ||||||||||||||
Maximum inlet temperature℃ | 75 (17.0) | ||||||||||||||
Maximum inlet temperature | 45 | ||||||||||||||
Cleaning PH range | 2-10 | 2-10.6 | 2-11 | 2-10 | |||||||||||
Maximum influent turbidity,NTU | 1-12 | 1-12 | 1-12.5 | 1-12 | |||||||||||
largest waterSDI15 | 1.0 | ||||||||||||||
Maximum influent residual chlorine concentration mg/L | ˘5 | ||||||||||||||
Ratio of minimum amount of pus to water production | 0 | ||||||||||||||
Maximum pressure drop of a single element pai(Mpa) | 5 : 1 | ||||||||||||||
model | 10(0.07) |
model | ESPA1-4040 | ESPA2-4040 | ESPA4-4040 | |||||
type | size | 4inches | ||||||
Membranematerials | Aromatic polyamide composite | |||||||
Effective film area | Ft2 | 85 | 85 | 85 | ||||
M³ | 7.9 | 7.9 | 7.9 | |||||
performance | Desalination ratebaifenbi% | average | 99.4 | 99.6 | 99.2 | |||
minimum | 99.2 | 99.0 | ||||||
Water production | gpd | 2600 | 900 | 2500 | ||||
m3/d | 9.8 | 7.2 | ||||||
The test conditions | NACL solution concentration mg/L | 1500 | 500 | |||||
Pressure,psi(Mpa) | 150(1.05) | 100(0.7) | ||||||
Temperature,℃ | 25 | |||||||
Recovery rate of single film element,% | 15 | |||||||
test liquid PH | 6.5-7.0 | |||||||
Maximum inlet pressure,psi(Mpa) | 600(4.14) | |||||||
Maximum inflow rate,gpm(m3/h) | 16(3.6) | |||||||
Maximum inlet temperature℃ | 45 | |||||||
Inlet ph range | 2-10 | 2-10.6 | 2-10 | |||||
Cleaning PH range | 1-12 | 1-12 | 1-12 | |||||
Maximum influent turbidity,NTU | 1.0 | |||||||
largest waterSDI15 | <5° | |||||||
Maximum influent residual chlorine concentration mg/L | <0.1 | |||||||
Ratio of minimum amount of pus to water production | 5:1 | |||||||
Maximum pressure drop of a single element pai(Mpa) | 10(0.07) |
Size | Weight | DIM | PLT |
4" | 4.5kg | 113*13*13cm | 81pcs |
8" | 14kg | 113*23*23cm | 25pcs |