Model Specification | MS-120-5 | MS-120-12 | MS-120-15 | MS-120-24 | MS-120-36 | MS-120-48 | ||||||
DC output voltage | 5V | 12V | 15V | 24V | 36V | 48V | ||||||
Output voltage error(Note,2) | ±2% | ±1% | ±1% | ±1% | ±1% | ±1% | ||||||
Rated output current | 24A | 10A | 8A | 5A | 3.3A | 2.5A | ||||||
Output current rage | 0-24A | 0-10A | 0-8A | 0-5A | 0-3.3A | 0-2.5A | ||||||
Wave and noise(Note ,3) | 75mVp-p | 75mVp-p | 75mVp-p | 50mVp-p | 50mVp-p | 50mVp-p | ||||||
Inlet stability(Note ,4) | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±5% | ±5% | ||||||
Load stability (Note ,5) | ±1% | ±0.5% | ±0.5% | ±0.5% | ±5% | ±5% | ||||||
DC output power | 120W | 120W | 120W | 120W | 120W | 120W | ||||||
Efficiency | 75% | 78% | 78% | 82% | 82% | 82% | ||||||
Adjustable range for DC voltage | +10,-5% | ±10% | ±10% | ±10% | ±10% | ±10% | ||||||
AC input voltage range | AC90~132v/180~264V (selected by switch)47~63Hz; | |||||||||||
Input current | 2.4A/115V,1.2A/230V | |||||||||||
AC Inrush current | Cold-start current 36A/230V | |||||||||||
Leakage current | <0.5mA/240VAC | |||||||||||
Overload protection | 105%~150% Tpye, Fold back current limiting Reset, auto recovery | |||||||||||
Temperature coefficient | ±0.03%/°C(0~50%) | |||||||||||
Setup rise hold up time | 200s,100ms,30ms | |||||||||||
Vibration | 10~500Hz,2G 10min,/1cycle,Period for 60min,each axes | |||||||||||
Withstand voltage | Input and output internal,1.5KVAC,Input and enclosure,1.5KVAC,Output and enclosure,0.5KVAC | |||||||||||
Isolation resistance | Input and output internal, Input and enclosure, Output and enclosure,500VDC/100MΩ | |||||||||||
Working temperature and humidity | -10°C~+60°C(Refer to output derating curve),20%~90%RH | |||||||||||
Store temperature and humidity | -20°C~+85°C,10%~95%RH | |||||||||||
Overall dimension | 157×97×38mm | |||||||||||
Weight | 0.55Kgs | |||||||||||
Safety standards | Meet UL1012 requirement(Not apply for the mark) | |||||||||||
EMC standards | ………… | |||||||||||
Note 1.The testing condition for the parameter above is ,230VAC input, rated load,25°C70% RH.Humidity. 2.Error.include the setting error,line stability and load stability.(Note:5). 3.Wave test:adopting "A12"double wire for 20MHz,and 0.1UF&47UF capacitor short-circuit for interrupting. 4.Inlet voltage stability test: when is over load, the lowest voltage of inlet is up to the highest voltage. 5.Load stability test: the load is from 0% to 100%. |