Beijing reci Long lifespan standard spt laser tube w8 price for laser machine part
We sale Beijing Reci EFR Yongli etc brand laser tube.
It's better you send to me model of laser tube. So that offer you best price.
There are also other laser machine parts for sale, like laser power supply, lens, controller system etc.
Reci S/W Series Long Lifetime co2 laser tube adopt new technique of production and inflation formula for co2 gas, to ensure the high quality and stability of glass laser tubes. The lifetime of laser tube is up to 10000 hours, laser power is from 80 watts to 180 watts, it is very popular in thickness materials cutting.
Parameter:
MODEL
|
RATED POWER
|
MAX POWER
|
LENGTH(mm)
|
DIA(mm)
|
CATALYZE
|
LIFE SPAN (h)
|
WARRANTY
|
W1
|
75W
|
90W
|
1050
|
80
|
YES
|
10000
|
18MONTHS
|
W2
|
90W
|
100w
|
1200
|
80
|
YES
|
10000
|
18MONTHS
|
W4
|
100W
|
130w
|
1400
|
80
|
YES
|
10000
|
18MONTHS
|
W6
|
130W
|
160w
|
1650
|
80
|
YES
|
10000
|
12MONTHS
|
W8
|
150W
|
180w
|
1850
|
90
|
YES
|
10000
|
12MONTHS
|
Application: CO2 laser cutting machine mainly, CO2 laser engraving machine.
It can be used to cut acrylic plate, MDF, leather, cloth, PVC, Paper, Rubber plate, Board and other non-metal material.
(a) The laser cooling water is distilled water or pure water, the temperature should be 20-30. In summer, the water temperature is high, should change the laser water chiller or stop the machine for a while. In cold area, don’t let the water freezing, especially don’t let the water stay in laser tube if the laser machine not work. (Attentions: customers who use alternating current must let the water box grounded).
(b) The two fixture should be installed in the 1/4 position of laser tube head. And the volume of water flowing is 2L-4L/min, if not, the cooling water effect is not good. It will let the coating of the tube easy fall off. Beams not focused and decrease the laser power. The nozzle of cooling water in chiller must be covered underwater. If not, the laser tube cannot full with water when next start.
(c) Please pay attention to protect the laser output window to avoid smoke sputtering during working as well as adjusting light path. When the laser output window is polluted, the laser power will be decreased. So please use absorbent cotton or cloth dipped in alcohol without water to clean the surface of laser output window.
(d) When installing, adjust the position of the tube fixture or rotate the laser tube to achieve the best effect. Then fix the laser tube up very well.
(e) Keep the high voltage cable and connector clean and dry. Far away from metal body.
(f) Don’t let scale deposit in the laser tube, it will decrease the cooling effect. If you find the scale deposit, please use 20% rare hydrochloric acid to clean scale of cool tube.
(g) It is glass laser tube, operate it carefully.
(h) Please use laser tube reasonably. The laser tube is used by the right ways, which will save laser power. In fact, the optimal laser power is only 80% for itself.
1. Installation Requirement
Make sure to follow the operation instruction of model W2 as shown in the illustration. The dedicated power P12 should be equipped. The positive pole of laser tube is in high voltage (the ignition voltage is 19kv). It may cause the following consequence when it is failed to follow the instruction: Arcing; the inner tube will be punctured by electricity and may cause water leakage.
2. Operation conditions
Water cooling: using purified water; 2 to 5 liter/minute; water temperature: 10℃-40℃.
The operating environment: temperature 2-40℃; Humidity 10-60%.
The working current: test current is 29mA. Maximum working current is 29mA. The running current must be kept below 27mA. The life span can reach 8,000 hours if the current is kept below 25mA. The ammeter must be connected to the negative electrode of laser tube.
When it is working under over-high current for long term, the negative pole will appearlight yellow and the life span will be shortened rapidly.
To protect dust from going into the insulation sheath, please wrap it with plastic film.
3. Working Performance
Cutting function.
Engraving function: Very good. When the working current is 4mA and the tube is in the state of preionization, the laser can be used for high-frequency impulse engraving.
4. Key Notes
Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror:
1) When the mirror is polluted, do not turn on the laser.
2) Blow the mirror surface sideways with an air blower.
3) Spray the pure alcohol on the mirror surface with sprayer.
4) Turn on the laser after the alcohol gets fully volatilized.
5) If the methods above don't work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean the mirror surface from middle to edge. The best solution is to prevent the window from being polluted.
Attention: it is forbidden to clean the mirror with acetone.
The screws in the front and back ends of the laser tube are not allowed to be moved, otherwise the output power will be declined, even the tube will be scrapped.
Put the acryl 300mm far away from output mirror, when testing its laser spot.
5. Safety
The laser beam is invisible light. Please wear protective glasses when debugging the laser. The positive pole is in high voltage. Pay attention to the security marks.
6. Storage and Transportation Requirement
Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag. The storage environment is 2-40℃, and the requested humidity is 10-60%. Pack the laser as in the original way.
Important notes: it is requested to use adhesive tape to cement the sponge together with laser tube to prevent the tube from vertically sliding during transportation. The sponge in the side of output mirror must be 70 mm beyond it, and the sponge in the side of reflecting mirror must be 50 mm wider.
Tubes operated in wrong way are not guaranteed by Manufacturer.
Jinan GoodCut CNC Machinery Co.,Ltd.
GoodCut has Purchasing department, The design department, The production department, Quality inspection department, packaging and transportation department, The sales department, After sales service department.
We can offer highest quality machine, and competitive price.
Jinan GoodCut CNC Machinery Co., Ltd.
The meaning of “GoodCut” brand: Good Quality, Good Price, Good Service
Good Quality
1. 15 engineers with more than 10 years rich working experience, manufacture high precision machines;
2. Three-day 72-hour testing machine inspection, after confirming that the machine has no quality problems, then it will be shipped;
3. 4 QC staffs do strict evaluations on in-coming inspections, in-process inspections and final inspections.
Good Price
1. GoodCut manufactures about 50 sets of machines per month, with a large sales volume. We have long-term cooperation with parts suppliers, can get advantageous prices of parts, so that the price of machine is very competitive;
2. GoodCut aims to develop long-term cooperation with new and regular customers, and to give customers the best prices with the most sincere attitude.
Good Service
1. English manual and video for machine using and maintaining, explaining the operation steps in detail;
2. Professional after-sales service staffs, providing 24-hour online service;
3. Provide free technical training and factory field operation teaching to eliminate customer worries.