Autoclaved Lightweight Concrete ALC Block Cross Cutting Machine Fabricator

Autoclaved Lightweight Concrete ALC Block Cross Cutting Machine Fabricator

 Automatic AAC Block Making Machine :flowchart 

                                                                          General Processing Description

Process

Typical stages involved in the AAC panel production process include raw material preparation, batching and mixing, pouring, pre-curing, cutting, autoclaving, and packing.

Indonesia Market AAC Block Making Plant/AAC Block Separator Packing Machine : overview

                                                            Batching

 Pouring Mixer

The pouring mixer is a key element on the AAC block production line. It keeps the concrete from hardening by constantly tumbling the mixture around. In the mixer, ingredients of desired proportion are blended and then poured into the mould for pre-curing.

                                                 Pre-curing and Cutting

Mould

The mould is a vessel into which concrete slurry is poured. In the mould, the slurry stiffens to form the green cake. The green care rises due to the evolution of hydrogen gas from the reaction between aluminum powder and rest of concrete slurry. The process is termed as pre-setting. Mould Turning Machine

The mould turning machine is mainly used to turn the pre-set concrete through 90 degree so that the mould can be easily removed from the concrete to facilitate cutting. This process leaves two side plates of the mould on the concrete. The purpose of side plates is to support the preset concrete and keep it from collapsing. After de-mould, the incomplete mould combines with two new side plates to form a complete one again, which readily accepts the next concrete pouring.

Cutting Machine

The cutting machine is used to precisely cut all the six sides of concrete cakes to various required dimensions. It is mainly made up of transfer car, vertical cutter, cross cutter, and car exchange device.

Tilting Table for Semi-product

As the cutting is completed, the green cake is tilted back by 90° so that it sits on its wide, lengthwise side. At this point, a scraper is used to remove the bottom waste as well as clean the bed. Wastes that are washed off into the pit will be recycled, which results in cost savings. All these motions are driven by hydraulic cylinder and controlled via proportioning valves to ensure stability. The big transfer car, small transfer car, tilting bed, and scraper are the major parts that make up the whole tilting system.

Stacker for Semi-product

The stacking machine is used to transfer the concrete panel together with the bottom plate of the mould to the de-moulding crane and the autoclaving car. It also returns the side plates of mould to the roller conveyor.

Indonesia Market AAC Block Making Plant/AAC Block Separator Packing Machine :stacker for semi-product 

                                          Curing and Final Product Handling

Curing Car

The curing car, also known as autoclaving car, is an integral part of the autoclaved aerated concrete production line. It carries the semi-finished concrete panels (which are seated on the bottom plate of the mold) to the autoclave.

Ferry Car

The ferry car is a kind of material handling equipment that travels across the line of AAC production. Thanks to this transfer trolley, the mould-carrying car and the cake-filled autoclaving car can run on each other’s rails.

Chain Conveyor

In the chain drive system, the sprocket receives power from the motor and transmits it via the chain to the driven sprocket installed on the tow-car. The tow-car then pulls other equipment back and forth along the rail, with the help of pushing and towing unit. Main parts of the chain conveyor include the transmission unit, towing unit (tow-car), and rear wheels. Autoclave

Autoclave is a large steam equipment which can be used in steaming sand aac block,flyash aac block and aac brick/panel.

Separator

After autoclaving, the piled-up concrete panels need to be separated along the cuts, one layer from the next. The purpose of separation is to keep each individual AAC panel from sticking to the adjacent ones. The separating operation is carried out by the separator, which is made up of the separating device and lifting device. The lifting motion of the separator is driven by a hydraulic power unit. Proportioning valves are used to control the hydraulic unit to ensure operating stability.

Clamping Machine

The clamping machine takes hold of each individual AAC block/panel and carries it to the packing line.

 Indonesia Market AAC Block Making Plant/AAC Block Separator Packing Machine :clamping machine

Packing Line

The packing line is designed for improved efficiency and reduced labor cost. A number of pallets are arranged along the packing line. Each individual AAC panel is lifted by the crane and put down on the pallet. Once the packing operation is started, the pallet together with the AAC panel moves along the packing line.

Annual Output Table

With decades of experience in serving the AAC blocks production machinery industry, we can supply customers with quality AAC block production lines with capacity ranging from 50,000m3 to 400,000m3 per year.

Welcome to visit our factory and AAC Block Making Plant/AAC Panel Production Line Machine  working site.