Welcome to TradeChina
Auto Expandable Polystyrene Styrofoam EPS Batch Pre-expander Making Machine
FOB Reference Price
Purchase quantity ()
Minimum order quantity
Payment
Meo Textile Clothing Co.LTD
China - Hangzhou
Manufacturer
Trade Capacity
Export Percentage
Nearest Port
shanghai,ningbo
Accepted Delivery Terms
Employees
101-200 people
Accepted Payment Currency
USD,CNY
Average Lead Time
60 Day(s)
Certifications
Product Specifications
Model Number
ESPB-50,ESPB-110,ESPB-150,ESPB-160
Product Description
Product Description
Product Details
EPS Production Technology - Pre Foaming:
Batch foaming
After weighing the EPS beads in batches, they enter the pre foaming machine for pre foaming.
-High precision of pre foaming
-Wide range of foaming density
-EPS raw materials with low pentane content can be prepared
-Generally, EPS raw materials contain 6-7% pentane
-EPS raw materials with low pentane content contain 3-4.5% pentane (pre released in a pressurized pre foaming machine)
*Methods of adjusting foaming density
– by adjusting the quantity of raw materials to be put in each time
– by adjusting the heating time of steam
– by adjusting the height of EPS beads in the foaming machine (at which point the steam is cut off)
– by adjusting the steam pressure
– by regulating the supply of steam (steam to air ratio)
Control mode of batch foaming
-Control steam pressure (0.1 to 0.6 bar) - low density
-Control steam temperature (85 to 99 ° C) - high density
-Air mixing - high density
EPS Pre Expansion Steps
1. Preheating
Open the cleaning door to remove the impurities in the cylinder, check whether the movable mixing rod is firm, and then close the cleaning door. Close the three valves on the control panel and close the feed gate. Start the mixing and feeding motor, and the mixing rod and feeding screw are idly running. At this time, open the steam valve to raise the temperature in the foaming cylinder to 70 ~ 75 ° C and keep it for 3 ~ 5 minutes.
2. Advance
Advance is divided into one advance and two advance. For one pre delivery, put about 8kg of raw materials into the hopper. After preheating, open the gate at the feeding port to make all the raw materials enter the pre launching machine. Close the feeding gate (at this time, the raw materials can be filled again). The raw materials in the machine will be released in advance gradually until the overflow source flows out of the pre sent beads. Open the raw material inlet to feed continuously, and at the same time, the overflow port continuously flows out the pre sent beads. At this time, it is necessary to adjust the valve and increase the temperature to obtain the best temperature.
Note: do not start continuous feeding, otherwise the load of the mixing motor will increase due to the serious deviation of the density of beads in the machine, resulting in shutdown or other serious consequences.
The second pre delivery is to put 6-7kg of the primary pre delivery beads into the secondary feeding hopper, open the feeding gate to carry out the secondary pre delivery, and at the same time, make the primary pre delivery device rotate to avoid the beads entering the primary pre launching device and pre sending, so as to block the primary pre delivery device. The feeding gate is opened to feed continuously until the bead particles flow out of the overflow port. According to the working conditions, the density of beads should be measured at intervals.
3. Density adjustment
A steam regulating valve is installed on the operation panel of the machine to control the amount of steam entering the pre generator. The steam pressure gauge indicates the value, which is generally controlled at about 0.15 ~ 0.2MPa. The operation panel is also equipped with a temperature regulating valve to regulate the inlet air temperature by controlling the amount of air blown in. At this time, the temperature inside the machine can be adjusted carefully according to the indicated value of the thermometer on the plate and the density of the pre sent beads. During the adjustment process, the temperature inside the machine needs about 30 seconds to stabilize, and the density takes 3 to 5 minutes to stabilize.
The adjustment of density can be realized by adjusting temperature, feeding speed and bead overflow. However, in the first pre delivery, the temperature is mainly regulated, while in the second pre delivery, the feed quantity is mainly adjusted, which is slightly different due to the different quality of raw materials. The same is true of the use and adjustment of machines that are only pre issued once or twice.
4. End of advance
Before the end of pre delivery, close the hopper inlet gate and stop feeding. The machine must continue to run, and the mixer still needs to work for 5-8 minutes, so that all the raw materials finally entering the machine can be pre dispatched. After the raw materials in the standby system are fully pre sent, the compressed air valve on the operation panel shall be opened first, and the steam valve shall be closed. When the temperature in the machine drops below 60 ℃, the compressed air valve shall be closed, and the lower small door shall be opened. Due to the agitation of the mixing rod, the remaining beads in the pre starter shall be continuously discharged from the small door. When the discharged beads are rare, the compressed air shall be opened intermittently to make the inside of the machine All the beads were discharged. Stop the machine, close all valves, open the cleaning door for thorough cleaning, and then cut off the main power supply.
Product Features
1.Five Safety Protection Device, With Safety Maintenance Guardrail On The Top;
2.The Whole Machine Adopts Touch Screen And Plc Control, All Parameters Can Be Set In The Touch Screen, And The Operation Is Simple;
3.The Barrel Material Of The Pre Expander In Contact With Eps Raw Material Is 304 Stainless Steel;
4.High Density Rock Wool Is Used As Thermal Insulation Layer For The Barrel Of The Pre Expander, Which Can Effectively Reduce The Temperature Change And Steam Energy Consumption Of The Barrel;
5.The Steam System Adopts Japanese Original "Yoshitake" Pressure Reducing Valve To Control The Steam Pressure To Ensure That Each Batch Of Foaming Steam Is Stable And Uniform;
6.The Raw Material Weight Of One Pre Issued Eps Is Controlled By Accurate Weighing Sensor To Ensure The Density Difference Between Each Batch;
7.The Design Of Constant Temperature And Constant Pressure Ensures That The Foaming Error Is Controlled Within 3%;
8.Equipped With Secondary Foaming System, It Is Convenient To Produce Eps Products With Lower Density;
9.The Fluidized Bed Is Equipped With A Special Drying System To Reduce The Aging Time Of Beads In The Silo, So As To Reduce Energy Consumption;
10.Low Voltage Electrical Components Are Schneider Brand, Pneumatic Components Are Airtec.
Hot-Sale Product
Product Application
Company Profile
Why Choose Us
Packing & Delivery
FAQ
1. Q: Where is your company located? How can I visit there?
A: Our factory is located in Hangzhou City, Zhejiang Province, China. Welcome to visit us.
2. Q. Do you have some videos where we can see the line producing?
A: Yes, we can provide some videos for reference.
3. Q: What's the MOQ?
A: Our MOQ is 1 Set.
4. Q: Can I have my own customized product?
A: Yes. Your customized requirements for color, logo, design, package, carton mark, your language manual etc. are very welcome.
5. Q: Can you produce according to the samples?
A: Yes, we can produce mold by your samples or technical drawings.
6. Q: What's the delivery time?
A: Generally, it will take 20 to 60 days after receiving your advance payment. The specific delivery time depends on the items and
the quantity of your order.
7. Q: What is the payment terms?
A: T/T, L/C, D/P at sight
8. Q: How does your factory carry out quality control?
A: We attach great importance to quality control.Every part of our products has its own QC.
9. Q: What certificate do you have?
A: We have TUV, CCC, CE (EN71, EN14765), SGS, ISO9001 etc. Also we can apply any certificate if you need if the qty is OK.
A: Our factory is located in Hangzhou City, Zhejiang Province, China. Welcome to visit us.
2. Q. Do you have some videos where we can see the line producing?
A: Yes, we can provide some videos for reference.
3. Q: What's the MOQ?
A: Our MOQ is 1 Set.
4. Q: Can I have my own customized product?
A: Yes. Your customized requirements for color, logo, design, package, carton mark, your language manual etc. are very welcome.
5. Q: Can you produce according to the samples?
A: Yes, we can produce mold by your samples or technical drawings.
6. Q: What's the delivery time?
A: Generally, it will take 20 to 60 days after receiving your advance payment. The specific delivery time depends on the items and
the quantity of your order.
7. Q: What is the payment terms?
A: T/T, L/C, D/P at sight
8. Q: How does your factory carry out quality control?
A: We attach great importance to quality control.Every part of our products has its own QC.
9. Q: What certificate do you have?
A: We have TUV, CCC, CE (EN71, EN14765), SGS, ISO9001 etc. Also we can apply any certificate if you need if the qty is OK.
No desirable products?
Sourcing assistant>
How to start your business
- Step 1Find your interested products by search keywords
- Step 2Contact the supplier by clicking ”Enquire” or “request meeting” button, otherwise, you also could consult our import consultant.
- Step 3After verifying your email, get response from suppliers or our trade manager will contact you as soon as possible
- Step 4Set up meeting with the Chinese supplier without language barrier
Related Categories
Plastic&RubberMachineryPartsPlasticProductMakingMachineryPlasticRawMaterialMachineryRubberProductMakingMachineryRubberRawMaterialMachineryRubberRecyclingMachineryPopular Searches
thermoplastic machineplastic dryer machineelastic tape machinethermoplastic paint machinethermoplastic rubber matride on scrubber machineelastic rubber webbingleather strap cutter machinethermoplastic paint remover machinecar plastic rubber coatingused plastic pet baler machinepvc plastic gutter cornerride on scrubber machineplastic packing machinerylaser mat cutter machinewaste plastic to fuel machinepet plastic drying machineplastic dryer machinethe plastique machinelaser cut silicone rubber machinetire crusher rubber machineelastic rubber webbingtpu elastic band machinethermoplastic paint machinethermoplastic extrusion machinesthermoplastic road marking machinerycrumb rubber machineryelastic rubber sheetlaser plastic welding machineplastic sleeper machineused rubber machineryjinde plastic machineryplastic fuel machinethermoplastic rubber sbselastic tape machinewheat flour machinerythermoplastic striping machineplastic slipper machinethermoplastic rubber toyswaste plastic crusher machine