ASTM B564 Inconel 600 UNS N06600 nickel alloy steel SO flange ASME B16.47
ASTM B564 Inconel 600 UNS N06600 nickel alloy steel SO flange ASME B16.47
|
Standard |
Type |
Class |
Size |
|
ASME B16.5 |
WN/LWN/SO/Blind/Lap Joint |
150#-2500# |
1/2"-24"(Except Blind Flange 2500lb 1/2"-12") |
|
SW flange |
150#-1500# |
1/2"-3"(Except 1500# 1/2"-2 1/2") |
|
|
Threaded |
150#-900# |
1/2"-24" |
|
|
1500# 2500# |
1/2"-2 1/2" |
||
|
ASME B16.47 Series A |
WN/blind flange |
150# -900# |
22"-48"(Except 900# Size:26"-48") |
|
ASME B16.47 Series B |
WN/blind flange |
75#-300# |
26"-48" |
|
400# 600# 900# |
26"-36" |
||
|
DIN2527 |
Blind flange |
PN6-PN100 |
DN10-DN1000 |
|
DIN2543 |
SO flange |
PN16 |
DN10-DN1000 |
|
DIN2544 |
SO flange |
PN25 |
DN10-DN1000 |
|
DIN2545 |
SO flange |
PN40 |
DN10-DN500 |
|
DIN2565 |
Threaded flange with Neck |
PN6 |
DN6-DN200 |
|
DIN2566 |
Threaded flange with Neck |
PN16 |
DN6-DN150 |
|
DIN2567 |
Threaded flange with Neck |
PN25 PN40 |
DN6-DN150 |
|
DIN2568 |
Threaded flange with Neck |
PN64 |
DN10-DN150 |
|
DIN2569 |
Threaded flange with Neck |
PN100 |
DN10-DN150 |
|
EN1092-1:2002 |
Plate flange for welding/loose plate flange with weld-on plate collar or for lapped pipe end/Blind Flange/WN flange |
PN2.5-PN100 |
DN10-DN4000 |
|
JIS B2220 |
Welding flange, lap joint flange, threaded flange |
PN6-PN100 |
DN10-DN1500 |
|
BS4504 BS10 TableD/E |
Plate Flange for welding/WN flange/blank Flange |
PN6-PN100 |
DN10-DN1500 |
|
Other Products |
Anchor/swivel/girth/lap joint/reducing/orifice |
||
|
Spectacle blind/paddle blind/spacer ring/orifice plate/bleed ring |
|||
|
Special Products: rings/forgings/disc/shaft sleeves |
|||
|
Sealing Surface |
RF FF RTJ TF GF LF LM |
||
|
Flange Face Finish |
Stock finish/spiral serrated/concentric serrated/smooth finish(Ra 3.2 and 6.3 micrometers) |
||
|
125-250 AARH(it is called smooth finish) |
|||
|
250-500 AARH(it is called stock finish) |
|||
|
Coating |
Vanish, yellow paint, anti-rust oil, galvanizing etc |
||
|
Material Grade |
Nickel Alloy Steel |
ASTM/ASME B/SB564 UNS N02200(NICKEL 200), UNS N04400(MONEL 400), |
|
|
UNS N08825( INCOLOY 825), UNS N06600(INCONEL 600), |
|||
|
UNS N06601(INCONEL 601), UNS N06625(INCONEL 625), UNS N10276(HASTELLOY C276), |
|||
|
ASTM/ASME B/SB160 UNS N02201(NICKEL 201), ASTM B/SB472 UNS N08020(Alloy 20) |
|||
|
Copper Alloy |
ASTM/ASME B/SB151 UNS C70600(CuNi 90/10), C71500(CuNi 70/30) |
||
|
Stainless Steel |
ASTM/ASME A/SA182 F304,304L,304H,309H,310H,316,316H,316L,316LN, |
||
|
317,317L,321,321H,347,347H |
|||
|
Duplex and Super Duplex Steel |
ASTM/ASME A/SA182 F44,F45,F51,F53,F55,F60,F61 |
||
|
Carbon steel |
ASTM /ASME A/SA105(N) |
||
|
Low Temp Carbon Steel |
ASTM/ASME A/SA350 LF2 |
||
|
High Yield Carbon Steel |
ASTM/ASME A/SA694 F52, F56 F60, F65, F70 |
||
|
Alloy Steel |
ASTM/ASME A/SA182 GR F5,F9, F11,F12,F22,F91 |
||
|
Titanium |
ASTM/ASME B/SB381 Grade 2, Grade 5, Grade 7 |
||
UNS Number N06600
Other common names: Alloy 600
Inconel 600 is a nickel-chromium alloy used for applications that require corrosion and high temperature resistance. This nickel alloy was designed for service temperatures from cryogenic to elevated temperatures in the range of 2000° F. It is non-magnetic, has excellent mechanical properties, and presents the desirable combination of high strength and good weldability under a wide range of temperatures. The high nickel content in Inconel 600 enables it to retain considerable resistance under reducing conditions, makes it resistant to corrosion by a number of organic and inorganic compounds, gives it excellent resistance to chloride-ion stress-corrosion cracking and also provides excellent resistance to alkaline solutions. Typical applications of this nickel alloy include the chemical, pulp and paper, aerospace, nuclear engineering and heat treating industries.
In what form is Inconel 600 Available?
• Sheet
• Plate
• Bar
• Pipe & Tube (welded & seamless)
• Fittings (i.e. flanges, slip-ons, blinds, weld-necks, lapjoints, long welding necks, socket welds, elbows, tees, stub-ends, returns, caps, crosses, reducers, and pipe nipples)
• Wire
What are the characteristics of Inconel 600?
• Resistant to a wide range of corrosive media.
• Virtually immune to chlorine ion stress corrosion cracking
• Non-magnetic
• Excellent mechanical properties
• High strength and good weldability under a wide range of temperatures
| Ni + Co | Cr | Fe | C | Mn | S | Si | Cu |
| 72.0 min | 14.0-17.0 | 6.0-10.0 | .15 max | 1.00 max | .015 max | .50 max | .50 max |
In what applications is Inconel 600 used?
• Chemical industry
• Aerospace
• Heat treating industry
• Pulp and paper industry
• Food processing
• Nuclear Engineering
• Gas turbine components
Fabrication with Inconel 600
Alloy 600 can be both hot formed and cold formed using typical processes. Hot working should be performed between 1600 F and 2250 F avoiding any work between1200-1600 F because the ductility decreases in this temperature range. Welding Alloy 600 can be achieved via shielded metal-arc welding, TIG, and MIG.
| Pipe Smls | Pipe Welded | Tube Smls | Tube Welded | Sheet/Plate | Bar | Forging | Fitting | Wire |
| B167 | B517 | B163 | B516 | B168 | B166 | B564 | B366 |
Typical room temperature Tensile Properties of Annealed Material
| Product Form | Condition | Tensile (ksi) | .2% Yield (ksi) | Elongation (%) | Hardness (HRB) |
| Rod & Bar | Cold-Drawn | 80-100 | 25-50 | 35-55 | 65-85 |
| Rod & Bar | Hot-Finished | 80-100 | 30-50 | 35-55 | 65-85 |
| Tube & Pipe | Hot-Finished | 75-100 | 25-50 | 35*55 | - |
| Tube & Pipe | Cold-Drawn | 80-100 | 25-50 | 35-55 | 88 Max |
| Plate | Hot-Rolled | 80-105 | 30-50 | 35-55 | 65-85 |
| Sheet | Cold-Drawn | 80-100 | 30-45 | 35-55 | 88 Max |
- Step 1Find your interested products by search keywords
- Step 2Contact the supplier by clicking ”Enquire” or “request meeting” button, otherwise, you also could consult our import consultant.
- Step 3After verifying your email, get response from suppliers or our trade manager will contact you as soon as possible
- Step 4Set up meeting with the Chinese supplier without language barrier