299H Model FISHER Pressure Reducing Gas Regulator 2inch Thread END Connection

299H Model Pressure Reducing Regulators LPG Regulator

Specifications for 299H Series constructions are given below. Some specifications for a given regulator as it originally comes from the factory are stamped on a nameplate located on the actuator upper casing.

Specifications

Available Constructions
Type 299H: Pilot-operated pressure reducing regulator with a pilot integrally mounted to the actuator casing.
Body Sizes and End Connection Style

2-inch FNPT 

Maximum Operating Inlet Pressure by Orifice Size
1/4 x 3/8 inch / 6.4 x 9.5 mm . . . . 175 psig / 12.1 bar
3/8 inch / 9.5 mm . . . . . . . . . . . . . . 175 psig / 12.1 bar
1/2 inch / 13 mm . . . . . . . . . . . . . . 175 psig / 12.1 bar
3/4 inch / 19 mm . . . . . . . . . . . . . . 150 psig / 10.3 bar
7/8 inch / 22 mm(5) . . . . . . . . . . . . 125 psig / 8.6 bar
1 inch / 25 mm(5) . . . . . . . . .. . . . . . . 100 psig / 6.9 bar
1-3/16 inch / 30 mm(5) . . . . . . . . . . . . . 80 psig / 5.5 bar
Maximum Casing and Emergency Outlet Pressure
66 psig / 4.5 bar

Pressure Control Accuracy (Fixed Factor) (PFM)
±1%(3) of absolute control pressure
Minimum Differential Pressure For Full Stroke
1.5 psid / 0.10 bar

Construction Materials
Actuator Upper Casings: Aluminum
Actuator Lower Casing: Aluminum
Pilot Spring Case: Aluminum
Actuator Diaphragm: Nitrile (NBR)
Pilot Diaphragm: Nitrile (NBR)
Pilot Inlet Screen: Stainless steel
Valve Body: Cast iron, Ductile iron, or Steel
Orifice and Valve Stem: Aluminum
Disk Holder: Aluminum holder with
Nitrile (NBR) disk
Main Disk Construction: Nitrile (NBR)
Metal Trim Parts For Pilot: Aluminum
Pilot Disk Construction: Nitrile (NBR)
O-Rings: Nitrile (NBR)
Fittings: Steel (standard) or Stainless steel
Tubing: Stainless steel

Features
• Compact in Size—Small envelope because of the built-in pilot and internal registration.
• Unique No Bleed Monitor System—Flexible worker/monitor system setup that allows for bleed to be piped to the intermediate piping thus eliminating downstream bleed which reduces lost and unaccounted for gas. Another advantage of this configuration is that the system lockup pressure is that of the worker instead of the monitor.
• Not an Adaptation of Existing Regulators—New design of integrated cases and internal registration ports.
• Wide Variety of Applications—Natural gas distribution systems, gas supply to industrial boilers, furnaces, ovens, mixers, plant air service.
• Highest Quality— Designed and manufactured
to ISO 9001 standards.
• Accuracy—Keeps constant inlet pressures to downstream equipment by accurately controlling distribution system pressures at widely varying flow rates and supply pressures for maximum efficiency and best operation, or by eliminating the need for pressure-compensating meters by holding a steady pressure to the meter inlet.
• Optional Token Relief—The Types 299HR and 299HSR with an integral token relief in the pilot is designed to relieve minor overpressure caused by thermal expansion.
• High-Capacity Pressure Control—Actuator diaphragm responds quickly to downstream 1pressure change, causing immediate correction in main valve position. Pilot responds simultaneously and controls final positioning of main valve. This action permits full main valve travel, resulting in higher capacity than could be obtained without an external pilot regulator.
• Easy Registration Conversion—Two screws and O-rings change internal registration to external or dual registration.
• Easy Startup—No special procedure required.

Outlet Pressure Ranges
 7-inches w.c. to 16 psig / 17 mbar to 1,1 bar

Pressure Registration
Internal and External depending on type number

Temperature Capabilities
-20° to 150°F / -29° to 66°C

Shipping Weight

21KG each one