1800C Tube Furnace with Ultrasonic Bubbler and Electrostatic Precipitator for Nano-Particle Formation - CY-1800X-PGEP
Introduction of ultrasonic bubbler electrostatic precipitator nano preparation furnace
CY-1800X-PGEP is a versatile synthetic system designed for nanosturctured oxide materials. Three major modules (Ultrasonic
Enhanced Bubbler, Tube Furnace and Electostatic Precipitator) are employed on three processing steps including aerosol
generation, thermal decomposition and nanopowder collection. Such a system enables advanced synthetic method that
provides control over particle size, morphology, nano/micro structure.
Specification of ultrasonic bubbler electrostatic precipitator nano preparation furnace
System Structure | Aerosol Generation: 2.4MHz Ultrasonic Enhanced Bubbler can "evaporate" catalyst liquid with literally no heat generated. A stainless steel liquid collector connects inline with the ultrasonic bubbler can prevent condensing liquid from streaming into the furnace tube chamber. Thermal Decomposition: Tube Furnace can be heated upto 1800C maximum. By passing the droplets flux across the temperature and atomosphere regulated firing zone, chemical and physical conversion processes proceed. Nanopowder Collection: 30KV, 2'' O.D tubular designed electrostatic precipitator can effectively collect nano size particles from the carrier gas flow | |
Tube Furnace - Thermal Decomposition | Voltage & Power | Single Phase, 208V~240V AC, 50/60 Hz (30A breaker required) Max. 2.5 KW |
Working Temperature | 1750oC continuous 1800 oC Max. < 1 hours | |
Max. Heating / Cooling Rate | 5oC / min ( T< 1600oC ); 2oC / min ( T>1600oC ) | |
Heating Zone & Constant Temperature Zone | 12" total heating zone length 3" ( +/- 1C ) constant heating zone | |
Heating Elements | 4 pcs Kanthal 1900ºC grade MoSi2 heating elements, made in Sweden | |
Temperature Controller | PID automatic control via SCR (Silicon Controlled Rectifier) power control with phase angle fired, current limiting resistor. 30 programmable segments for precise control of heating rate, cooling rate and dwell time. Built-in over temperature alarm and protection allows for operation without attendant. +/- 1 ºC temperature accuracy. RS485 Communication Port. | |
Processing Tube | Premier grade high purity Al2O3 ceramic tube is included for operation @ 1500C~1800C. (I.D: 44mm x OD: 50 mm x 1200 mm length). Attention: carrier gas flow rate should be strictly controlled @ 100SCCM or less. Mullite tube (I.D: 44mm x OD: 50 mm x 1398 mm length) is included for continuous operation upto 1500C. Benefits from its high thermoshock resistivity, it can endure a max. carrier gas flow rate @ 200SCCM. | |
Sealing Flanges & Fittings | Left sealing flange with 1/4'' feedthrough, needle valve and mechanical pressure gauge. A 1/4'' O.D x 17'' L alumina tube is inserted to the main chamber. It can deliver the aerosol to the hot zone directly. Right KF50 quick disconnect flange provides direct coupling for the electrostatic precipitator. Water cooling feature can be added with additional fee applied. | |
Aerosol Generation | Utrasonic Enhanced Bubbler | 110VAC, 2.4 MHz Utrasonic Generator Fluoropolymer coated liquid containtor and Fluoropolymer sealing gaskets external Fluoropolymer optical sensor and valve for keeping the liquid level to the correct height and preventing damage to the nebulizing element, should the unit run dry. Ultrasonic power programmable,0~100%, 5% increment. 304 Stainless Steel T-piece (1.5'' sanitary fitting) with 1/4'' tube fitting adaptors enables the use of carrier gases. |
Mass Flow Controller | A MFC is employed to control the carrier gas flow rate. It is very important that the gas flow must be controlled <100SCCM in order to minimize the thermoshock impact on the furnace tube. | |
Condensing Liquid Collector | 316 stainless steel made container, 150ml Two SS needle valves with 1/4" Tube Fittings The cap is attached to the body with quick disconnect clamp. This allows easy removal of components for cleaning | |
Nanopowder Collection | High Voltage Supply | 208~240VAC Single Phase, 15W max. Digital Voltmeter and Current meter, 30KV, 0.5mA max. Output voltage and current can be set by using knobs on the front panel and read from the digital display Constant current/Constant Voltage mode of operation Built-in Arc Protection Circuit |
Tubular Electrostatic Precipitator | Negative charged circular mesh plate and Positive charged 1'' O.D x 170mmL Al tube collector are built into a transparent 2'' O.D x 450mm L quartz tube The use of KF50 quick clamp and flange enables the quick coupling to the furnace processing tube Adjustable balance supports keep the collector leveled with the furnace tube | |
Warranty | One year limited manufacture warranty with life time support (consumable parts such as furnace liner, processing tubes, and O-rings are not covered by the warranty, please order replacements at related products below). |
System structure of ultrasonic bubbler electrostatic precipitator nano preparation furnace
Mass controller of ultrasonic bubbler electrostatic precipitator nano preparation furnace
Condensing Liquid Collector of ultrasonic bubbler electrostatic precipitator nano preparation furnace
Other types of ultrasonic bubbler electrostatic precipitator nano preparation furnace
1. Factory prices with the best quality.
2. One year free-of-charge maintenance for all the dental equipment
3. Customized service for special demand
4. Fast and flexible delivery, by sea, by air, by express
5. Quick response within 24 hours
How to order
1. If you are interested in our products, please tell us the model number and quantity.
2. We will make a proforma invoice for your order.
3. We will deliver the product ASAP on receipt of the payment
Guarantee
1. Guarantee for one year after shipment.
Payment
1. Western Union
2. PayPal
3. Secure Payment through Alibaba
4. Telegraphic transfer
5. L/C
Zhengzhou CY Scientific Instrument Co., Ltd is mainly engaged in the research and development, design, manufacturing andsales of equipment used in scientific researches. Independence and innovation is the company's tenet.Our main products
include: tube furnace, muffle furnace, plasma cleaner, vacuum furnace, atmosphere furnace,CVD system and customized
lab equipment.Welcome you come to visit us.